Quick Start Guide ProFace X (DS) Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
1 Overview Near-infrared Flash Microphone Camera 8-inch Touchscreen Under-screen Card Reading Area Tamper Switch Speaker Reset Button RS232 RS485 Wiegand Out Wiegand In 12V 12V GND GND GND RXD1 TXD1 485B 485A GND 12V +12V GND Power interface WD1 WD0 INWD1 INWD0 GND 12V GND AUX GND SEN GND BUT NO COM NC ALAL+ Network interface Note: Not all products have the function with , the real product shall prevail.
2 Installation Environment Please refer to the following recommendations for installation. 10ft window ft 6.5 KEEP DISTANCE AVOID GLASS REFRACTION AVOID DIRECT SUNLIGHT AND EXPOSURE KEEP EFFECTIVE DISTANCE 0.3-2.5m 3 Device Installation Install on the wall ① Attach the mounting template sticker to the wall, and drill holes according to the mounting paper. ② Fix the backplate on the wall using wall mounting screws. ③ Attach the device to the backplate.
3 Device Installation Install on the barrier gate Please thread the wire through the bracket before installation. ① Drill a hole on the barrier gate, insert the bracket into the hole and fix it with a nut. ② Adjust the angle of the device.
4 Standalone Installation Smoke Detector Alarm Door Sensor Exit Button Reader Lock TCP/IP PC 5 Door Sensor, Exit Button & Alarm Connection Detector Power + - COM NO Smoke Detector Exit Button Alarm + + - Alarm Power 4 GND AUX GND SEN GND Door Sensor BUT NO COM NC ALAL+
Lock Relay Connection The system supports Normally Opened Lock and Normally Closed Lock. The NO LOCK (normally unlocked when power-on) is connected with 'NO' and 'COM' terminals, and the NC LOCK (normally locked when power-on) is connected with 'NC' and 'COM' terminals. Take NC Lock as an example below: 1) Device not sharing power with the lock 2) Device sharing power with the lock GND +12V DC12V Maximum 30V 3A input.
8 Barrier Connection 12V 12V GND GND GND RXD1 TXD1 485B 485A GND 12V Barrier gate 9 RS485 Connection 12V 12V GND GND GND RXD1 TXD1 485B 485A GND 12V +12V GND 485485+ GND 485 reader Note: 485A and 485B can be connected to the Barrier gate or the 485 Reader, separately, but cannot be connected to the gate and reader at the same time.
10 Power Connection 12V 3A DC Recommended power supply: 12V - 3A To share the power with other devices, use a power supply with higher current ratings. 11 Ethernet Connection Connect the device and computer software over an Ethernet cable. An example is shown below: ZKBioSecurity Default IP address : 192.168.1.201 Subnet mask : 255.255.255.0 IP address : 192.168.1.130 Subnet mask : 255.255.255.
12 User Registration When there is no super administrator set in the device, click on to enter the menu. After setting the super administrator, the system will request for the administrator’s verification before entering the menu. For the security purpose, it is recommended to register a super administrator at the first time you use the device. Method1: Register on the device Click on > [User Mgt.] > [New User] to register a new user.
Method2: Register on ZKBioSecurity software Please set the IP address and cloud service server address in the Comm. Menu option on the device. 1. Click [Access] > [Access Device] > [Device] > [Search Device] to search the device on the software. When an appropriate server address and port is set on the device, the searched devices are displayed automatically.
Method 3: Register on the phone 1. Click [Personnel] > [Parameters], input ‘’http://Server address: Port’’ in the QR Code UGL bar. The software will automatically generate a QR code. Scan the QR code or login onto ‘’http://Server address: Port/app/v1/adreg’’ by the mobile phone to register users.
13 Access Control Settings Click on > [Access Control] to enter the access control management interface and set relevant parameters of access control. Main Menu Access Control Options Access Control Gate Control Mode Access Control Options User Mgt. Personalize Print User Role COMM. System Autotest Door Sensor Delay (s) Holidays L Data Mgt.
15 Detection Management Click on > [Detection Management] to enter the setting interface. 1 You can enable mask detection function, and enable the Deny Access Without Mask and the Trigger External Alarm, the device will send an alarm prompt when the user doesn’t wear a mask, meanwhile the user will be forbidden to access, as shown in the following figure. 2 When the Allow Unregistered People to Access is enabled, you can also set Enable Capture of Unregistered Person to save the user photo.
16 Multi-face Identifying Settings Click on > [System] > [Face] > [Face Identifying Settings] > [Identifying Mode] > [Multi-face Identifying] to enter the setting interface. When the Multi-face Identifying is enabled, the device can perform facial recognition of multiple people at once. For more details, please refer to the User Manual. Main Menu System Face Anti-Spoofing Settings Date Time User Mgt. Personalize Print User Role Data Mgt. Autotest COMM.
17 Video Door Phone Connection Visitors click the on the main interface of the device to call and the phone will ring. The user can select accept or decline the call. After the user accepting, it will enter the video door phone interface. 1. On the device, click on > [System] > [Video Intercom Parameters] > [QR Code Binding]. 2. Download and install the ZSmart APP on the phone, open the APP and add the device by scanning the QRcode.
18 QR Code as the Mobile Credential 1. In [System] > [Basic Management] > [Parameters] of ZKBioSecurity software, set Enable QR Code to “Yes”, and select the QR code status according to the actual situation. 2. On the server, choose [System] > [Authority Management] > [Client Register] to add a registered App client. 3. Open the APP, enter the IP address or domain name of the server, and its port number, scan the Register QR-code.
ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 Fax : +86 755 - 89602394 www.zkteco.com Copyright@2022 ZKTECO CO., LTD. All Rights Reserved.
