Installation Guide Model: HBL400 Version: 1.
Important Notes 1. Please read this Installation Guide carefully and contact the Customer Care Service if you have any questions about the installation. 2. To avoid any future service charges that can arise as a result of incorrect installation, it is recommended that installation can be performed by a professional technician to prevent any potential service charges that can occur due to incorrect installation. 3.
What's in the Box Outdoor Unit Indoor Unit Keys Lithium Battery Spindle A Spindle B Strike Plate and Box Cylinder Screw A Mounting Plate Screw B Screw C 1 Mortise Cards Metal Pin Screw D Stud
Installation Diagram OLED Screen Indoor Unit Door Screw C Lithium Battery Outdoor Unit Spindle A Screw D Metal Pin Stud Hidden Cover Screw A Metal Pin Screw D Cylinder Spindle B Screw C Screw B Screw A Keys Mounting Plate Mortise Strike Plate and Box Front Handle Cover Installation Procedure 1 Door Properties A. Measure the Door Thickness Measure the thickness of the door and select the appropriate Spindle length. For further details, please refer the table on Page 1. B.
Mortise Strike Plate Mortise Strike Plate Mortise Right Inward Left Inward Mortise Strike Plate Strike Plate Right Outward Left Outward User Location Adjust the Direction of Latch (if needed) 1) Push the reverse block in upward direction. 2) Push the bolt of the latch into the mortise. 3) Rotate the latch bolt to 180° inside the mortise, and release it. 2 Drill Holes on the Door 1) Place the installation template at the desired height.
3 Install Mortise and Cylinder 1) Put the Mortise into the hole that was drilled, and secure the Mortise with Screw A. 2) Insert the Cylinder into the Mortise ( the front sides and back sides) and secure it with Screw B. Screw A Screw B Front Front 4 Uninstall the OLED Screen and Mounting Plate 1) Uninstall the OLED screen by pushing up, then uncover the hidden cover from the bottom of indoor unit. 2) Uninstall the screw D and take the Mounting Plate off the indoor unit.
5 Install Studs and Outdoor Unit 1) Install the studs on the back of outdoor unit. 2) Pass the outdoor unit cable through the upper most cable hole. 3) Attach the Outdoor unit to the door by inserting the studs through the drilled holes. 4) Place the Mounting Plate on the inside door and use Screw C to secure them. Stud Screw C 6 Install Indoor Unit 1) Install Spindle A and Spindle B with Metal Pin. 2) Connect the cable to the port on the Indoor Unit.
7 Install Batteries and Cover Insert Lithium Battery and cover them with an OLED Screen model, then push back the hidden cover. 8 Install Strike Plate and Box 1) Make sure that the Strike Box is aligned with the latch bolt. Then, use the installation template to drill the holes. 2) Align the Strike Plate and Box with the holes drilled and protect them with Screw A. Screw A 31mm 171mm 261mm 22mm 2 .
Physical Test Test the lock by using the mechanical key. 1) Uncover the front handle cover from the bottom of outdoor unit, then rotate the cover 90°. 2) Press the bottom of key hole cover and rotate it 180°. 3) Insert the Key into key hole and rotate 90°, then the latches will be retracted.
User Manual Model: HBL400 Version: 1.
Important Notes 1. HBL400 is an intelligent Smart Lock. If the lock is not installed properly, it may affect the lifetime of the lock. We suggest you to install the lock after furnishing. Please prefer a professional technician to install the lock as per our installation standard. 2. Please initialize the lock after installation and set the Administrator immediately to avoid others opening the door illegally. 3. To ensure your security, please check the box of keys when opening the product package. 4.
Table of Contents Product Overview...........................................................................................................1 De nitions......................................................................................................................1 How to Use......................................................................................................................2 1. Reset the Lock............................................................................................
Product Overview Camera Keypad & Card Detection Area Fingerprint Sensor (Hidden) Mechanical Key Hole (Hidden) 3D Structured Light Facial Recognition Model Indicator Light Lithium Battery Handle OLED Screen Model Hidden Cover Handle Clutch Emergency Power Interface (Micro USB) Double Locking Knob Quick Unlock Button Front Handle Cover Quick Close Button Reset Button Definitions User Roles: The lock can be handled by two user roles namely Administrator and User.
Emergency Charging: The bottom of the outdoor unit is provided with a Micro-USB interface. Use a power bank to charge the lock when it is out of power. Emergency Mechanical Key: The mechanical key is used to open the door when the lock has electronic malfunction. Double Locking: Double locking prevents the lock from being unlocked from the outside. Users can enable it by rotating the double locking knob.
4 Register the First Administrator Press and hold the Reset button for 5 seconds. The lock will beep for 5 times. Keep holding the Reset button until you hear the audio prompt, please press # key to confirm. 1) Touch the keypad to activate the lock. 2) Press the * # key to start the registration process. The user will hear a prompt “Please register administrator, please enter fingerprint, password, access card, press star to exit”.
Note: 1) The first administrator can not be a Face. 2) While registering the Face, you need to look at the 3D Structured Light Facial Recognition Model for few seconds. 3) To delete the Face, only do that by entering the number. 4) The 3D Structured Light facial recognition function is not really suitable for strong sunlight environments, if unlock at this environments, please verify with fingerprint/password/card/key.
Quick Start Attention: If the verification has failed for five times consecutively, the lock will generate an alarm. Unlocking Door with Face Stand in front of the smart lock about 60cm apart Look at the 3D Structured Light Facial Recognition Model Note: It will wake up and verify your face automatically. If it does not wake up automatically, then you need to wake up the lock manually.
How to use OLED Screen Model? Overview Up/Power Off Down/Back OK/Power On Programming the Features through Menu Mode 1) Press Power On button to activate the model (camera mode). 2) Press Down button to enter menu, choose Camera, Files or Set mode freely through buttons.
Camera: Go to camera mode, customer can watch outside through the camera on outdoor unit. Files: All of photographs and videos are saved at here, before using this function, please insert a TF on this model. Set: It is used to set functions of this model. As below: 1) Record Mode: Choose Photograph or Record (video) as records saving mode. 2) Continuous Shooting: Set the number of pictures one shooting, two or five, press OK button to shoot at camera mode.
How to connect USmart Go APP? Setting Step 1: Download the App Search "USmart Go" on Apple App Store or Google Play Store on your iOS/ Android device. Step 2: Create an Account Launch the "USmart Go" App and register an account, you can register by your phone number or email address.
Step 4: Setting Security Password You'll need to setup a security password for two-step verification. Following are the steps: Menu -> "My Settings" -> "Set security password". Step 5: Connect the Lock Lanuch the App, click “+ Add Device” button directly (only fit for no device before situation), or click the "ADD" button at the upper right corner, choose "Add Wi-Fi Device" item, you'll see Connect hotspot page. 1) Press the "* #" key and verify administrator on the lock to enter administrator menu.
Note: 1) Please close WLAN on your phone setting page before connecting. 2) Please select "No" or "Use" if your phone suggest you to switch to another Wi-Fi when connecting Wi-Fi. Step 6: Finish After getting connected, please go back to Connect hotspot page, and wait for the page until it goes to Select Wi-Fi page then connect a valid Wi-Fi and wait until finish. Note: Please close Cellular Data if you are staying on Connect hotspot page for a long time after connecting Wi-Fi.
Functions 1. Remote Unlock Guest Require: Press "Doorbell" key twice within 30s on the keypad to trigger a remote unlock request then you'll see a popup window on our app where you need to enter your security password to unlock. Owner self-unlock : Click the Unlock icon, you'll see a popup window on our app then enter your security password to verify and press the "Doorbell" key once, the lock will unlock.
2. Add User Click “Password” button on lock page, then click “+” on the top right corner to change to Add User page and fill out the authorizations information, then click “Next” to generate password. Note: Password is 7digits on the Generate password page, the last one is “1” by default.
3. Name the Lock Click the “More” button on the lock page, a popup window will be appeared, choose “Settings” to go to the Setting page, then click the Device Name to rename this lock and after finishing, click OK button. 4. Mark the App Remote Unlock Person to be a User Click an unlock event to go to the Edit User page, then name the user at the blank, after finishing, click OK button.
5. Check Records All of the event records are displayed on the lock page, customer can click them to check.
Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
