PRODUCTS MANUAL R2G SERIES Micro Redundant Power Supply For 2U Chassis
INDEX 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.
1.1 INTRODUCTION First of all, thank you for purchasing R2G Series – Micro Redundant power supply for 2U chassis. The R2G is an 1+1, Hot-swappable/Hot-pluggable, Micro Redundant power supply set, it consists of: (1) complete metal frame (nickel-plated) (2) compact size (smaller than PSII form factor) 1+1 power modules (3) backplane board The R2G Series of hot swappable micro redundant power supply offer a maximum 300/350 watts of output power.
1.2 PACKING Your R2G box package should consist of the following: (A) R2G *1 (B) Accessory pack (included 1 holding bracket for shipment)*1 (C) Products’ manual *1 1.3 MODEL DESIGNATION Model number identification: R2G - 63ZZX R 2G 6 3ZZ X --- Redundant (AC Input) --- suit for 2U chassis (1U = 44.4 m/m) --- for 6 DC outputs (5V/12V/-5V/-12V/3.3V/5VSB) for ATX12V / EPS12V Spec. --- total output power, 3ZZ- 300,350 (unit: watt) --- can be P or F. P for built in PFC (full range).
1.
INPUT CHARACTERISTICS: R2G-6300P VOLTAGE: 95 ~264 VAC FULL RANGE FREQUENCY : 47 ~ 63 Hz INPUT CURRENT: 6.0 / 3.0 A FOR 115 / 230 VAC INRUSH CURRENT: 60A / 80A MAX. FOR 115 / 230 VAC PER POWER MODULE OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN.[A] MAX.[A] PEAK(A) REGULATION OUTPUT LOAD LINE RIPPLE & NOISE MAX. [P-P] ± 5% ± 1% 50mV ± 6% ± 1% 120mV 5V 3.0 32 12V 2 16 -5V 0.05 0.5 ±10% ± 1% 120mV -12V 0.05 0.8 ±10% ± 1% 150mV 3.3V 1.0 20 ± 5% ± 1% 50mV 1.
INPUT CHARACTERISTICS: R2G-6350P VOLTAGE: 90 ~ 264 VAC FULL RANGE FREQUENCY : 47 ~ 63 Hz INPUT CURRENT: 8.0 / 5.0 A FOR 115 / 230 VAC INRUSH CURRENT: 60A / 80A MAX. FOR 115 / 230 VAC PER POWER MODULE OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT MIN.[A] MAX.[A] PEAK(A) REGULATION OUTPUT LOAD LINE RIPPLE & NOISE MAX. [P-P] 5V 3.0 35 ± 5% ± 1% 50mV 12V 2 22 ± 5% ± 1% 100mV -5V 0.1 0.5 ±10% ± 1% 150mV -12V 0.1 0.8 ±10% ± 1% 150mV 3.3V 1.
1.8 INSTALLATION & TESTING Turn off (Remote off) the on/off switch. Mount the power supply in the system chassis using the proper mounting tool, the mounting holes in the power supply should match up with those in the case. Attach the connectors to the M/B by following the M/B instructions, there are various on connectors / pinouts in both power supply and M/B. They should match each other; otherwise the connection will cause undetectable harms.
If everything works out fine, then turn off (remote off) the power system, now put back the cover of the case and tighten with the screws which you have retained earlier. Now you have completed the installation of the R2G redundant power supply system. 1.9 HOT-SWAP PROCEDURES Please refer to the following when either power module or the fan found defective. A) Locate the defective power module by examining the individual LED (if LED without light, it indicates the power module is defective).
D) Replace a new Good power module, insert the power module into the power system to the end. E) Check the LED of the power module light Green. F) Check the LED which indicates the total power system status, that should be from twinkle to Green. G) Tighten the screws of the power module to fix it. H) If you want to test this new power module in simulating defective situation. Please refer to the Section 1.8 Installation & Testing Section.
THE BUZZER RESET SWITCH CONNECTOR (300W MODEL) PIN# COLOR VOLTAGE 1 YELLOW +12V 2 BLACK GND THE BUZZER RESET SWITCH CONNECTOR (350W MODEL) PIN# 1 2 COLOR YELLOW BLACK THE SIGNAL CONNECTOR OF POWER RESET PIN# COLOR 1 RED 2 BLACK TTL signal : Sink current max. 5mA Source current max.
1.11 TROUBLE SHOOTING If you have followed these directions correctly, there should be no problem occurred. Some common symptoms are: the system doesn’t work, buzzer sound, work for a very short period, etc., please try the following steps to verify and correct it: 1. Check all the connections (correct pinouts, loose connections, wrong direction, etc). 2. Check for short-circuits or defective peripherals by unhooking each peripheral once at a time.
The “RELIABILITY “ solution to E-application 新巨企業股份有限公司 ZIPPY TECHNOLOGY CORP. POWER DIVISION HEADQUARTERS 10F, NO. 50, MIN CHYUAN RD., SHIN-TIEN CITY, TAIPEI HSIEN, TAIWAN, R.O.C. TEL: 886-2-29188512 FAX: 886-2-29134969 WEB SITE: http://www.zippy.com.tw E-mail：power@zippy.com.tw USA OFFICE U.S. East (Atlantic) 11 Melanie Lane, Unit 1B East Hanover, NJ 07936 TEL：1-973-463-9499 FAX：1-973-453-8014 E-mail：edward@zippy.com U.S.
