User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 User Manual Product Type: Model Name: Switching Power Supply HG2, HP2, PSM, PSL June 18, 2003 Version 1.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Table of Contents Safety and Warnings ............................................................................3 Product and Accessories.......................................................................4 Pin Assignment ....................................................................................5 Specification…………………………………………………………..8 Operational Procedures ......................................................................
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Safety and Warnings IMPORTANT INFORMATION ON SAFETY AND PROPER OPERATION OF THE POWER SUPPLY. << Read the information carefully before using it. >> 1. Do not attempt to take apart the power supply. There are hazardous voltages inside. 2. Do not add or remove any components from the power supply. Warranty void by doing so. 3. Only authorized technician or service center is allowed to open the power supply for product services. 4.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Product and Accessories Please contact your local dealers if any of the following product or accessory is missing from the package. 1. Power Supply Unit. (Refer to the Figure) 2. Screws x 4. To prevent missing screws during shipment, screws were installed on the power supply. When install power supply into computer, remove those four screws first, please do not remove fan or case screws. All four screws should be installed and fasten. 3.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Pin Assignment Always check the socket and pin assignment (for devices such as motherboard, Hard Disk etc.) before connecting the two heads. E P S PIN NO. COLOR O UTPUT PIN NO. CO LOR 1 O RANGE +3.3V 13 ORANGE +3.3V 2 O RANGE +3.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 PIN NO. EPS COLOR OUTPUT PIN NO. COLOR OUTPUT 1 BLACK GND 5 YELLOW +12V 2 BLACK GND 6 YELLOW +12V 3 BLACK GND 7 YELLOW +12V 4 BLACK GND 8 YELLOW +12V 8PINS (EPS12V) PIN NO. COLOR OUTPUT PIN NO. COLOR OUTPUT 1 RED +5V 5 BLACK GND 2 GREY PWR-OK 6 YELLOW +12V 3 BLACK GND 7 YELLOW +12V 4 BLACK GND 8 YELLOW +12V 8PINS (AMD,ATX-GES) PIN NO. COLOR OUTPUT PIN NO.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 PIN NO. COLOR 1~3 ORANGE +3.3V 4~6 BLACK GND 7~9 RED +5V 10~12 BLACK GND 13~15 YELLOW +12V OUTPUT 15PINS (SERIAL ATA HD) PIN NO. COLOR OUTPUT PIN NO. COLOR OUTPUT 1 YELLOW +12V 3 BLACK GND 2 BLACK GND 4 RED +5V 4PINS (HD／CD-ROM/RW) PIN NO. COLOR PIN NO.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Specifications Please refer to the specifications according to the actual product purchased. Note: The new feature, “Prolonged Cooling” after power supply is remote-off only available on model HG2. Under normal conditions, when power supply is at “Remote-off” mode, cooling fan will remain in operation for the secondary heat dissipation, and will come to stop at a much lower temperature. This will prolong the life of the power supply.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Specifications Please refer to the specifications according to the actual product purchased. INPUT CHARACTERISTICS: HP2-6460P/6500P VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. INPUT CURRENT: 8.0 A FOR 115 VAC, 4.0 A FOR 230 VAC. INRUSH CURRENT: 65 A MAX. FOR 115 VAC, 125 A MAX. FOR 230 VAC. OUTPUT CHARACTERISTICS: M IN .[A] M AX .[A] LO AD LIN E O U T PU T R IPPLE & N O ISE M AX . [P-P] 5V 2.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Specifications Please refer to the specifications according to the actual product purchased. INPUT CHARACTERISTICS: PSM-6550P/6600P VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. INPUT CURRENT: 10.0 A FOR 115 VAC, 5.0 A FOR 230 VAC. INRUSH CURRENT: 65 A MAX. FOR 115 VAC, 125 A MAX. FOR 230 VAC. OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT REGULATION OUTPUT MIN.[A] MAX.[A] LOAD LINE RIPPLE & NOISE MAX.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Specifications Please refer to the specifications according to the actual product purchased. INPUT CHARACTERISTICS: PSL-6701P VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. INPUT CURRENT: 10.0 / 11.0 / 12 A FOR 115 VAC, 5.0 / 5.5 / 6.0 A FOR 230 VAC. INRUSH CURRENT: 65 A MAX. FOR 115 VAC, 125 A MAX. FOR 230 VAC. OUTPUT CHARACTERISTICS: MIN.[A] MAX.[A] LOAD LINE OUTPUT RIPPLE & NOISE MAX. [P-P] 5V 2.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 INPUT CHARACTERISTICS: PSL-6720P/6800P/6850P VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. INPUT CURRENT: 5A (RMS) FOR 220 VAC 12A (RMS) FOR 110 VAC INRUSH CURRENT: 75A MAX. FOR 110 VAC 150A MAX. FOR 220 VAC OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT(A) MIN. MAX. +5V 0.5 +12V REGULATION PEAK OUTPUT RIPPLE & NOISE MAX. [P-P] LOAD LINE 45 ± 5% ±1% 60mV 2 52/60/60 ± 5% ±1% 120mV -5V 0 0.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 INPUT CHARACTERISTICS: PSL-6A00V VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. STEADY-STATE CURRENT: 14/7A AT ANY LOW/HIGH RANGE INPUT VOLTAGE INRUSH CURRENT: 20A MAX. FOR 110 VAC , 40A MAX. FOR 220 VAC (AT 25 DEGREE C AMBIENT COLD START) PFC: UP TO THE TARGET OF 95% @230V, FULL LOAD OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT (A) REGULATION OUTPUT RIPPLE & NOISE MAX. [P-P] MIN. MAX.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 INPUT CHARACTERISTICS: PSL-6C00V VOLTAGE: 90 ~ 264 VAC FULL RANGE. FREQUENCY: 47 ~ 63 Hz. STEADY-STATE CURRENT: 15/7.5A AT ANY LOW/HIGH RANGE INPUT VOLTAGE INRUSH CURRENT: 20A MAX. FOR 110 VAC , 40A MAX. FOR 220 VAC (AT 25 DEGREE C AMBIENT COLD START) PFC: UP TO THE TARGET OF 95% @230V, FULL LOAD OUTPUT CHARACTERISTICS: OUTPUT VOLTAGE OUTPUT CURRENT (A) REGULATION OUTPUT RIPPLE & NOISE MAX. [P-P] MIN. MAX.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Operational Procedure 1. When removing four attached screws to install this product, please make sure not removing fan or case screws by mistake. 2. Tighten four screws onto the computer case and double check for stability. (Please refer to the figure on page 4). 3. Before connecting the units, make sure you verify connector and pin assignment for devices such as motherboard, hard disk etc.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Troubleshooting & Maintenance SYMPTOM No power? Power is on, but no monitor display? COUNTERMEASURE After plug main connector, such as 24-pin or 20-pin and aux. connectors if needed, to motherboard socket, make sure AC power cord gets AC line source that is on wall outlet, to this product power supply. If AC power cord gets AC line source through power bar or UPS, turn on these devices first.
User Manual for Models HG2, HP2, PSM and PSL. Version 1.0 Technical Support To best serve our customers, there are several services available to suite your needs: 1. For detailed products specification: please visit www.zippy.com 2. For technical enquiries: please send e-mail to powersales@zippy.com 3. For RMA service: please prepare following items before calling RMA department, Proof of purchase (original dated receipt) Product serial number (SER. NO.
