ZP19056 ASSEMBLY INSTRUCTIONS ROGER RABBIT VINYL GARDEN FENCE 3-PACK (24” W X 22” H) ASSEMBLY INSTRUCTIONS ZP19056 30 MIN Approximate assembly time for 3 fence panels Want to see a video on how to assemble this product? Scan the QR code WWW.ZIPPITY-OUTDOOR.COM 1 VER.
ZP19056 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT k Check the inside of the larger pieces in your box for other materials packed inside. k When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. k We recommend an area approximately 5’x 8’ for unobstructed assembling. k You should not need to use excessive force when assembling components.
ZP19056 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B G H D C Rail End Cap (12) (6 installed, 6 loose) Post Anchor (6) ¾” x 1¼” x 12” Post Cap (6) Joiner Clip (6) Top Rail (3) 1½” x 1½” x 24” E Bottom Rail (3) 1½” x 1½” x 24” I F ¾” Steel Screw (24) Bag A J Picket (24) ¼” x 1¼” x 21½” WWW.ZIPPITY-OUTDOOR.
ZP19056 ASSEMBLY INSTRUCTIONS STEP 2: ASSEMBLE FENCE FRAME STEP 2.1 Identify the top rail (C) and the bottom rail (D). Insert (2) rail end caps (G). Note: Top rail can be identified by the picket holes in both sides of the rail. C G D 3 STEP 2.2 1. Position (2) posts (F) as shown. 2. Slide top rail over posts and align pre-drilled holes. 3. Drive (4) ¾” steel screws (I) into the pre-drilled holes. 2 Align 1 F Tabs facing down STEP 2.
ZP19056 ASSEMBLY INSTRUCTIONS STEP 3: INSERT THE PICKETS STEP 3.1 Tabs E Rotate the fence frame so that the 1 post tabs are facing up. Insert (8) pickets (E) into the 2 picket holes in the top and bottom rails. STEP 4: ASSEMBLE ADDITIONAL PANELS STEP 4.1 Repeat Steps 1-3 to assemble the other two fence panels. WWW.ZIPPITY-OUTDOOR.
ZP19056 ASSEMBLY INSTRUCTIONS STEP 5: INSTALL FENCE INTO GROUND STEP 5.1 1. Move the fence panel to its final location, and mark the location of the posts. 2. Attempt to push fence panel into the ground until the post anchors are entirely in the ground. 1 2 Push into the ground with your hands STEP 5.2 Steps 5.2-5.3 are only to be completed if ground is too hard for Step 5.1. 1. Loosen the top 6” of ground with claw hammer. 2. Add water to loosen soil. 3.
ZP19056 ASSEMBLY INSTRUCTIONS STEP 5.3 If ground is too hard, dig two 8” diameter 8” deep holes to accommodate two posts each as shown below. 8” diameter x 8” deep. STEP 5.4 Level the fence panel, backfill excavated dirt, and tamp as necessary. WWW.ZIPPITY-OUTDOOR.
ZP19056 ASSEMBLY INSTRUCTIONS STEP 6: INSTALL POST CAPS AND CONNECT PANELS STEP 6.1 1. Push the post caps (A) down over the posts to lock into place. 2. Straight Line Applications: Using (2) joiner clips (H) and (4) 1” steel screws (J), connect the panels as shown below. 3. Corner Applications: Using (2) joiner clips and (4) 1” stainless steel screws connect the panels at a 90° angle as shown below. A 1 J H 2 3 8 WWW.ZIPPITY-OUTDOOR.
ZP19056 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 support@zippity-outdoor.com 704-892-5222 877-234-6196 WWW.ZIPPITY-OUTDOOR.COM 10 WWW.ZIPPITY-OUTDOOR.
