Oceanside Outdoor Vinyl Shower Kit (3’ x 3’ Enclosure) A B A S S E M B LY G U I D E R E Q U I R E D F O R I N S TA L L AT I O N • (A) Zippity Post Extension for In-Ground Installation (Sold as 4-Packs) • (B) Zippity Galvanized Steel Surface Mount for Concrete or Wood Surface (Sold as 2-Packs) • (C) Standard Shower Curtain & Hooks (Purchase Anywhere) www.zippity-outdoor.com Ver 1.
Measurements 48 1/8 in 37 1/8 in 35 5/8 in 41 in Top View 61 5/8 in 88 3/4 in 80 in 77 in 35 1/4 in 42 1/8 in Front View 2 46 5/8 in Oceanside Outdoor Vinyl Shower Kit 60 in 10 in 35 1/8 in 39 1/8 in Side View
IInnttrroodduuccttiioonn && O Ove verrvviieew w Getting Started First off, allow us to say thank you for the investment you have made in one of our fine shower kits. This kit is designed to be assembled and installed ideally by two people with basic carpentry knowledge and tools. Do not attempt alone, especially during the installation stage.
Outdoor Shower Materials Overview Zippity DO-IT-YOURSELF FRIENDLY PRODUCTS 8 6 5 1 7 3 4 9 13 10 11 12 2 1. 2. 3. 4. 5. 6. 7. 4 Post Caps (4) Post - A (1) Post - B (1) Post - C (1) Post - D (1) Beams (2) Decorative End Caps (4) Oceanside Outdoor Vinyl Shower Kit 8. Shade Slats (9) 9. Rail Brackets (8) 10. Privacy Boards (6) 11. Wall U-Channel (4) 12. Wall Horizontal Rails (4) 13.
1 Outdoor Shower Materials Breakdown Check Boxes (Total of 3) for These Contents In the event of missing or defective parts please call our customer service dept. at 1 877 234 6196 (Mon. to Fri. 8:00 AM to 4:00 PM EST). 1. Post Caps (4) 2. Post - A (1) 2” x 3 1/2” x 87 3/8” 3. Post - B (1) 2” x 3 1/2” x 87 3/8” 4. Post - C (1) 2” x 3 1/2” x 87 3/8” 5. Post - D (1) 2” x 3 1/2” x 87 3/8” 6. Beams (2) 1 1/2” x 4 1/2” x 48” 7. Decorative End Caps (4) 10 8. Shade Slats (9) 9. Rail Brackets (8) 10.
Shower Additional Materials List A B CDE Hardware (in plastic bag) NOTE: WE HAVE INCLUDED 10% EXTRA SCREWS BEYOND WHAT IS IDENTIFIED BELOW. F All Screws Included with this Kit are Self-Auguring. A. Tube of Vinyl Weld Glue B. 1 3/8” Self-Auguring Stainless Steel Screws (16) (to Secure Beams to the Posts) C. 1 3/8” Self-Auguring Stainless Steel Screws (12) (to Secure Wall U-Channels to the Posts) D. 1 3/8” Self-Auguring Stainless Steel Screws (18) (to Secure Shade Slats to Beams) E.
Mounting on Wood Deck or Concrete Surface? This shower can be installed on a pre-existing wood or concrete surface using our Zippity Galvanized Steel Surface Mount (sold separately as 2 Packs).
STEP ONE Installation with Surface Mount 1 Insert Surface Mount as illustrated into the bottom of all four posts. 1 Surface Mount will be secured to the post in the next step. STEP ONE Installation with Post Extension 1 Insert Post Extension illustrated into the bottom of all four posts. 1 30 in 28 in Post Extension will be secured to the post in the next step. Note: The remainder of this instruction will be illustrated using the Surface Mount. Installation with Post Extension will be very similar.
STEP T WO 1 Install Brackets and U-Channels to Post 1 Layout Post A (marked at top of post) on a horizontal surface and align brackets with pre-drilled holes on post. Orientate the brackets as illustrated and secure to the post with 2 screws. Ensure that surface mount is installed fully (or post extension is installed as per page 8) prior to securing brackets to post Orientate the brackets as illustrated 2 Secure the U-Channel to the post between the brackets as illustrated using 3 screws.
1 Post A STEP THREE Assemble Two Side Panels 2 People Required 1 Orientate Posts A and B as illustrated. See page 4 for overview reference. 2 Insert bottom rail as illustrated into brackets (groove in rail facing up) Tip: Push the rail tight into the back of the bracket. The screw head may provide for a slight conflict, but with enough force it will “pop” inside the rail pocket. 3 Secure the bottom rail into brackets with 2 screws in each bracket as illustrated.
S T E P T H R E E ( Co n t ’d. . . ) 4 4 5 Insert first privacy board into bottom rail as illustrated. Angling the board as illustrated will make it easier to get into the channel on post and bottom rail 5 Insert last privacy board as illustrated, in similar fashion as the first privacy board. 6 2nd Insert Fully 2nd Slide the middle privacy board in vertically from the top as illustrated.
1 STEP FOUR (2 People will be required) 1 With a helper, Slide Shower Rods into the lower (smaller) routed holes on the posts until they bottom out inside the posts as illustrated. Insert Beams 2 Slide one of the beams thru the routed holes in the front two posts. Orientate as illustrated. 3 Slide the second beam thru the routed holes in the back posts. Orientate as illustrated. Note: Holes on the top of beam to be facing up.
1 STEP FIVE Final Adjust and Secure Beam to Post 3” 1 Beams should extend 3 inches beyond post. 2 Secure the beams to the posts by installing 2 screws on front and back of each post. 2 STEP SIX Install Post and End Caps 1 Pressure fit the post caps onto the post as shown. 2 Apply a small amount of vinyl glue to the inside of the end caps and attach to the end of the beams as shown.
Rear Wall 35 1/8 in 89.1 cm STEP SEVEN Square and Secure Post using Surface Mounts 1 48 3/8 in 122.7 cm 2 Measure and mark out the locaton of the posts. Diagonal distances must be the same to ensure square installation. 3 Use 1/4” x 2 1/4” wedge or concrete anchors (not included) to secure to concrete or similar sized lag screw with washer for mounting to wood. F Gate Opening 14 Marker Please Note: Concrete patios generally have sloped surface for water run-off.
STEP EIGHT Install Shade Slats 1 1 Orientate the shade slat as illustrated and fasten a screw thru the pre-drilled hole fully until it comes out the bottom of the shade slat. 2 Place the shade slat on the beams guiding the tip of the screws into respective positions in pre-drilled holes on beams as illustrated.. 3 Final secure the shade slats to the beam as illustrated. 4 Final secure the remaining shade slats in the same way. 2 5 Install your shower curtains according to the packaging instructions.
