White Black Espresso For assistance with assembly contact us.
White / Black / Espresso Corner Desk Parts List Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures. Using the incorrect hardware will cause damage.
1 4pcs Bolt 4 Ø1/4”x 1-1/4”L 23pcs Cam Lock 7 Hinge 10 Bolt 13 2 2pcs 1pc Ø5/32” x1”L 4pcs Wood Dowel 5 Cam Bolt 8 Screw 11 32pcs 3 23pcs Screw 6 12pcs Cover 9 Ø1/8”x1/2”L 1pc Plastic Cap Lock Washer Care and Cleaning Instructions: Before using, wipe with a clean, dry cloth. Periodically apply furniture wax to renew the finish. Avoid rubbing or scratching the surface with rough or abrasive objects.
White / Black / Espresso Corner Desk Assembly Instructions Please do not over-tighten cam locks. Please stop when you feel them 8 tighten. Attach hinges (7) to drawer front panel 7 L (K) and drawer front stretcher (L) by using screws (8) as shown. K Figure 1 Insert cam locks (4) into holes on Cam lock holes facing up drawer back panel (N) and drawer front stretcher (L). Screw cam bolts (5) into holes on drawer right panel (G).
Repeat the same procedure as above to attach drawer right side panel (G) to drawer back panel (N) and drawer front stretcher (L). Make sure the cam lock holes are facing upwards. Cover cam lock holes with covers (6). Then attach wood knob (9) to drawer front panel (K) by using screw (10). Figure 3 Screw cam bolts (5) into corresponding holes on the bottom of wood top (A).
Insert cam locks (4) and wood dowels (2) into corresponding holes on assembled unit from figure 3. Figure 5 Attach assembled unit from figure 5 to wood top (A) by inserting wood dowels (2) and cam bolts (5) into corresponding holes until assembled unit from figure 5 and wood top (A) meet. Tighten by rotating cam locks (4) clockwise with Phillips screwdriver. Cover cam lock holes with covers (6).
Insert screws (3) into bottom stretcher (D). Attach bottom stretcher (D) to left long shelf (E) by inserting screws (3) 3 into predrilled holes on left long shelf (E). Tighten screws (3) with Phillips D screwdriver. Make sure to insert the screws through the big hole on bottom stretcher (D) E rather than the small hole. Figure 7 Insert cam locks (4) into corresponding holes on back panel (I) and assembled Cam lock holes facing up unit from figure 7.
Insert cam locks (4) into holes on Holes facing out assembled unit from figure 8. Screw cam bolts (5) into holes on back leg (J). 2 Attach back leg (J) to assembled unit from figure 8 by inserting wood dowels (2) and cam bolts (5) into corresponding holes until assembled unit from figure 8 and back leg (J) meet. Tighten by rotating cam locks (4) clockwise with Phillips screwdriver. Cover cam lock holes with covers (6).
Cam lock holes facing up Insert cam locks (4) into holes on back panel (I) and assembled unit from figure 10. Screw cam bolts (5) into holes on right side leg (C). Attach back panel (I) and assembled unit from figure 10 to right side leg (C) by inserting wood dowels (2) and cam bolts (5) into corresponding holes until assembled unit from figure 7 and back panel (I) and right side leg (C) meet. Tighten by rotating cam locks (4) clockwise with Phillips screwdriver. Cover cam lock holes with covers (6).
Insert cam locks (4) into holes on assembled unit from figure 12. Screw cam bolts (5) into holes on the bottom of wood top (A). Attach wood top (A) to assembled unit from figure 12 by inserting wood dowels (2) and cam bolts (5) into corresponding holes until assembled unit from figure 12 and wood top (A) meet. Insert bolts (1) through lock washers (13) and flat washers (12) to connect assembled unit from figure 12 and wood top together.
Turn the table over and slide drawer shelf (M) into the slides of unit as shown. Figure 15 Insert plastic cap (11) into the hole on the wood top (A) as shown.
Parts Replacement Form Customer Information Name Address City/State/Zip Code Phone Number Please indicate where you purchased this item: Store/Website/Catalog Please indicate color/size/style number: Style No Parts Letter Parts Description Quantity Needed Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame.
