ASSEMBLY INSTRUCTIONS Tools Required for Assembly: ASSEMBLY RATING Phillips Screwdriver The Assembly Rating is a 5-point system that (Not Included) shows the degree of effort needed in assembling a specific product (with 1 being Phillips Screwdriver � easy and 5 being difficult). For most 11/2 "L (Not Included) products.two persons are recommended.
Thank you for your purchase! We hope you will enjoy your new product for many years to come. Our commitment to providing quality products does not simply end when a purchase is made. We stand behind our products and will provide any support needed in order for you to fully enjoy your purchase. Your satisfaction is the greatest recognition we could have. Because we value your trust in our company,we will do our best to meet your service expectations.
ASSEMBLY & CARE ADVICE FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE. BASIC ASSEMBLY TECHNIQUES 1 It is highly recommended that the assembly should be done near the area of its intended location. Make sure you have enough space to move around during the assembly. Position each part correctly and insert screws or bolts into their respective holes by hand tighten or using the proper hand tool.
PRE-ASSEMBLY INTRODUCTION Unless you are particularly adept at assembling flat-pack/knock-down furniture, we understand building ready-to-assemble furniture can be a frustrating experience for some. To help avoid confusion and to make the assembly process quicker and smoother, we have provided some helpful tips. Before you begin the assembly, please read the following 1. 2. 3. 4. 5. 6. 7.
CAMLOCK FASTENER ASSEMBLY INSTRUCTIONS Note: Every cam lock bolt must have a cam lock connector in order to fasten the parts together. { 1} Align the cam connector with its side opening (or arrow) pointing to the small drilled hole. Secure the threded end of the cam bolt by using a screwdriver. Tun right (clokwise) to tighten. (3) (2) Insert the cam lock bolt into the pre-drllled hole above the cam connector. (4) Two parts should fit snugly against each other.
PARTS LIST �. 15� 12 27 15 � 13 11 15 � 2 22 (1) (2) (3) (4) (5) (6) (7) lpc lpc lpc lpc lpc lpc lpc (8) I (9) (10) I (11) I (12) : (13) I (14) 2pcs 3pcs 2pcs lpc lpc lpc 4pcs (15) I (16) (17) I (18) I (19) : (20) I (21) 3pcs lpc lpc lpc lpc lpc 2pcs (22) 1 (23) (24) 1 (25) 1 (26) : (27) 2pcs 4pcs 2pcs 2pcs lpc 2pcs 1 1 : 1 Before you begin,please read"Assembly and Care Advice","Pre-Assembly lntroduction"and "Cam Lock Fastener Assembly Instructions".
HARDWARE LIST - - - - - A B - C - - - - - - � o - - - - 1 === - - - - - - - - - L29 ¢15 - - - - ¢8x25 - - - - - - - - - - 40pcs 40pcs - - - 38pcs - - - � � � � � p � � � � � � 188] � � � � � � � � � � ��2 � � � � � � � � � � � � 2)�c� � � � E � 6pcs ¢4x35 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - F � (Jp-- - - - - 16pcs ¢4x3O - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
ASSEMBLY INSTRUCTIONS Page 8 of 21
ASSEMBLY INSTRUCTIONS Page 9 of 21
ASSEMBLY INSTRUCTIONS Page 10 of 21
ASSEMBLY INSTRUCTIONS Page 11 of 21
ASSEMBLY INSTRUCTIONS Page 12 of 21
ASSEMBLY INSTRUCTIONS Page 13 of 21
ASSEMBLY INSTRUCTIONS 15 15 15 Page 14 of 21
ASSEMBLY INSTRUCTIONS , /, ,, , , _, ,JJJ ,,,, _, ,JJJ Q Ax4 Cx4 � �o t4 ,, , '; ,,,, , Page 15 of 21
ASSEMBLY INSTRUCTIONS 0� CxlO BxlO � Page 16 of 21
ASSEMBLY INSTRUCTIONS 10 10 Page 17 of 21
ASSEMBLY INSTRUCTIONS Page 18 of 21
ASSEMBLY INSTRUCTIONS �\ �Qx� Rx4 Page 19 of 21
ASSEMBLY INSTRUCTIONS Page 20 of 21
ASSEMBLY INSTRUCTIONS SAFETY STRAP TO PREVENT TIP OVER SAFETY STRAP TO PREVENT TIP-OVER Drywall: Select a location where you want the table to be mounted. Place the assembled table against the wall and, on the wall, mark the location where the anchor will be placed. Drill a hole slightly smaller then the size of the screw . Push the anchor as far as it will go with your finger. Tap gently with a hammer until the anchor is flush with the wall surface.
