ZIP HydroTap G4 ® User Manual • • • • • Tap Functions..................(Pages 2-4) Tap Operation..................(Pages 5-10) LCD Screen & Menu .......(Pages 11-22) Maintenance.................... (Pages 23-26) Contact details.................(Page 28) Date of Installation............./........../........... CS Residential Affix Model Number Label Here 802269 For safe keeping store this book in the inside door pocket 802269 - Residential CS & CSHA User Manual - 09.2016 v3.
3. Tap functions HydroTap Classic: Chilled Lever Sparkling Lever The HydroTap Classic uses lever controls, to dispense Chilled and Chilled Sparkling water. There are Blue indicator lights, built into the levers, to show the status of the chilled water.
. Tap functions HydroTap Arc/Cube: On powerup, wait 30 secs. for the unit to calibrate. Tapping the select button will allow the selection of either the Chilled (BLUE) or Sparkling (White) water mode. The Arc/Cube control may be rotated in a forward or reverse direction to dispense Sparkling or Chilled water. The rotary control is spring loaded in the anticlockwise direction and when released, will return to the OFF position. When rotated clockwise the tap operates in a “Pot fill” mode.
3. Tap functions Celsius Arc/Cube: On powerup, wait 30 secs. for the unit to calibrate. The Celsius rotary control may be rotated clockwise to dispense Sparkling water or anti-clockwise for Chilled water. The rotary control is spring loaded and when released, will return to the OFF position. The mixer control operates in a conventional way to dispense Hot and ambient water direct from the customers mains and hot water service. The mixed water is not filtered, unless an external filter has been fitted.
3. Tap operation - Chilled To dispense chilled water: (Classic Tap) To dispense Chilled water: Press or Pull the Chilled lever Depressing the “Chilled” lever allows the dispensing of Chilled water. Pulling forward the lever allows the tap to operate in a “no-touch” mode. Water will flow from between 5 and 15 seconds (This is user adjustable). To reset, return the handle to the “Off” position and repeat the step. The lever must be manually returned to the “Off” position.
3. Tap operation - Chilled HydroTap Arc/Cube: Indicator light If not showing BLUE, tap the select button until the indicator light turns BLUE. Rotating the control, when the indicator light is BLUE, allows the dispensing of chilled water. Select button Arc/Cube Tap Celsius Tap: Rotate for Chilled water Turn the rotary control anti-clockwise to dispense chilled water as shown Page 6 of 28 802269 - Residential CS & CSHA User Manual - 09.2016 - v3.
Tap operation - Sparkling To dispense Sparkling water: (Classic tap) Press or Pull the Sparkling lever To dispense Sparkling water: Depressing the ‘Sparkling’ lever allows the dispensing of Sparkling water. Pulling forward the lever allows the tap to operate in a in a “no-touch” mode. Water will flow from between 5 and 15 seconds (This is user adjustable). To reset, return the handles to the “Off” position and repeat the step. The lever must be manually returned to the “Off” position.
Tap operation - Sparkling Indicator light HydroTap Arc/Cube: If showing BLUE, tap the select button until the indicator light turns WHITE. Rotating the control , when the indicator light is WHITE, will allow the dispensing of sparkling water. When unattended, the control light will automatically default to the Chilled (BLUE) mode after 30 seconds. Select button Arc/Cube Tap Turning the rotary control allows the dispensing of either Chilled Sparkling or Chilled water.
Tap operation - Mixer The Mixer tap lever is operated as a conventional ‘Flick Mixer’. The hot side is marked with a red stripe and the cold side with a blue stripe, for dispensing cold to warm water. Lifting the handle up will decrease the flow rate and lowering the handle will increase the flow rate. Lift the handle all the way up to turn the tap off. When the handle is moved towards the blue mark, the temperature is decreased and when moved towards the red mark, the temperature is increased.
Tap lights Filter light: (Classic, Elite & AIO taps) Filter light Filter Change Light Off: This indicates the filter is operating within its normal specified lifespan. Filter Change light flashing slowly: The light will flash slowly when the filter is due for replacement and the LCD will show “Filter Change”. Refer to “Replacing the filter” in section ‘C’ of this document. Filter light Turn filter light OFF: (All models) Refer to “Filter Reset” in section ‘C’ of this document.
3LCD Screen Zip HydroTap G4 introduces a ‘TOUCH’ screen for easy setup and operation adjustment.
3LCD Main Menu Language Screen Menu Sub Menu • English A • Product Info Information • System Faults • Filter Flush • Filter Reset • Purge CO2 • Lux sensor Service Security Communication • Product serial no.
A LCD Screen operation - Section A Set Language 1. Press [MENU] for main menu. 2. Press [Language] button. 3. Select an option to change the language 4. Press [<=] button for the previous menu LCD Screen operation - Section B B System Information In this section, you can find product information, system faults and filter log messages. 1. Press the [MENU] button for the main menu. 2. Press the [Info] button to view the current product serial number and other key information 1.
LCD Screen operation - Section B 1. Press [Energy] to view Energy information. 2. The Total energy consumption will be displayed, or 3. Select a date to view the energy used for that period 4. Press [<=] for the previous menu or press [Home] to return to the home screen. LCD Screen operation - Section C Install C Once your Zip HydroTap G4 unit has been installed, select the Install menu to configure the system settings for your product.
LCD Screen operation - Section C 1. Press the [MENU] button for main menu. 2. Press the [Install] button. Turn the 3. 4. Note: Run at least 10 Ltrs of water through to flush the filter of any excess black carbon particles (this is normal), before pressing the Stop button.Once the filter flush has finished, press the Stop button to display the main menu 5. 6. stop cock ON. Press the [Filter Flush] button. Press [Start] [Stop] buttons to start and Stop the filter flush.
LCD Screen operation - Section C 3 - Purge CO2 When fitting a new gas bottle, it is important to purge the gas lines. 1. Press the [MENU] button for main menu. 2. Press the [Install] button. 3. Press the [Purge CO2] button. 4. In the next screen, press the 5. 6. 7. 8. [START] button to commence the purging process. Wait for the water to stop flowing through the unit. Wait a further 10 seconds after the water has stopped flowing. During this time you will hear the CO2 gas escaping through the tap.
6 - Reset 1. Press [MENU] for main menu. 2. Press [Install] . 3. Press [Reset]. to reset the factory default settings LCD Screen operation - Section D D Service This section is reserved for service technicians only Note: In Australia call a licensed electrician, plumber,or Zip office on 1800-638-633, for assistance, service, spare parts, or enquiries. 3.
LCD Screen operation - Section F F Communication - WiFi (Select models) This section allows the user to use WiFi to monitor the product remotely. 1. From the Home screen Press [Menu]. Then [Comm’s] 2. Enter your 4 digit password to access the WiFi set up. 3. Follow the set up instructions supplied with the WiFi unit To disable the WiFi setup 1. Press [WiFi setup] 2. In the next screen Press [Disable] 3.
3. LCD Screen operation - Section G g Instructions G Settings 1. Press the [MENU] button for main menu. 2. Press the [Settings] button. 3. Press [Enable Password]. 4. Then enter your 4-digit password. You will need to enter your password to access the settings screens. If you have forgotten the password, please disconnect the power and restart your HydroTap unit. Set Date / Time HydroTap G4 Set Date/Time Screen 1. Press the [MENU] button for main menu. 2. Press the [Setting] button. 3.
3. LCD Screen operation - Section G tions Filter Zip HydroTap G4 allows the user to adjust filter life and edit filter usage. Note: The filter life may be set as a function of Litres used, or in months from the filter change. When the first of these functions is reached (i.e. Litres or months expired), the filter warning light will be illuminated on the tap. Either of these functions may be disabled (See below). To edit the filter life: 1. Press [MENU] button for main menu. 2. Press [Setting] button. 3.
LCD Screen operation - Section G Energy Modes This mode allows the HydroTap to enter into an Energy Saving mode. There are two options available: ‘Sleep’ mode and ‘ON/OFF’ mode. In SLEEP MODE the unit will go to “Sleep” after a 2hr period of inactivity. The Chilled water will be ON or OFF. When the period of inactivity passes, the home screen status window will show “Sleep Mode”. To activate the sleep mode: 1. Press [MENU] button for main menu. 2. Press [Setting] button. 3. Press [Energy Modes] button. 4.
LCD Screen operation - Section G In ON / OFF Mode the user may turn the unit ON or OFF at specific times for individual days or alternatively by weekly and/or weekend settings. To activate ON/OFF mode: 1. Press the [MENU] button for main menu. 2. Press the [Setting] button. 3. If required, Enter your 4 digit 4. 5. 6. 7. password Press the [Energy Modes] button. Select ‘Individual set’ if you wish to allocate a specific time for each day.
LCD Screen operation - Section G Dispense Times The ability to change the maximum dispensing time has been introduced. The default settings for the maximum dispensing times is 15 seconds. Here, the operator may change the Chilled and Sparkling dispensing times, to between 5 and 15 seconds, in increments of 1 second. To edit the dispensing times: 1. 2. 3. 4. Press the [MENU] button for main menu. Press the [Setting] button. Press the [Dispense Time] button.
Filter Maintenance • Caution: a small amount of water will drip as the cartridge is removed. • Do not tilt the cartridge as water may spill from it if tilted. • Unpack replacement cartridge and remove sanitary cap, write today’s date where shown on the label. • Avoid touching the filter O-rings and filter opening as this may cause bacterial contamination of the cartridge.
Gas bottle change 1. Turn the CO2 bottle regulator OFF (Anti-clockwise). The knob will screw up 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. and away from the bottle. Remove the bottle from the cupboard and disconnect the regulator. If the braided hose is removed from the regulator, be careful not to loose the small plastic sealing olive, located inside the end of the hose. Fit the regulator and hose assembly to the new gas bottle. Be aware that some CO2 may be discharged from the bottle joint.
Cleaning General cleaning Do not use strong, corrosive, spray or abrasive cleaners. Clean with a soft damp cloth and mild soap. Under sink units must never be located near, or cleaned with water jets. Avoid using airborne pesticides near the undersink unit. Page 26 of 28 802269 - Residential CS & CSHA User Manual - 09.2016 - v3.
Home Menu Icons Sleep mode is active. There are 3 sleep mode options which display this icon on the home screen. See page 17 for details. 50% Filter use. This icon displays the filter usage remaining from 100% (New filter) to 0% (end of life). When it reaches 0% the filter warning light on the tap head will flash slowly. The filter life can be adjusted by litres and by days used. See page 16 Chilled Temperature The set temperature of the water in the Chiller tank will be displayed.
Contact Details Head Office Zip Heaters (Aust) Pty. Ltd. ABN: 46 000 578 727 67 Allingham Street Condell Park NSW 2200 Postal: Locked Bag 80 Bankstown 1885 Australia Website: www.zipwater.com Facsimile: (02) 9796 3858 Telephone: (02) 9796 3100 Free Call: 1 800 638 633 As Zip policy is one of continuous product improvement, changes to specifications may be made without prior notice. Images in this booklet have been modified and may not be true representations of the finished goods.
