Installation Guide

THIRD ANGLE
PROJECTION
R
Configuration : Default
135
186
48
234
338 50 min. 50 min.
333
333
200 min.
A
A
Mains cold water
isolation valve
(not supplied)
240 - 230V,
50Hz GPO
Clearance
Envelope
CO
2
Cylinder
Inlet Vent
Ventilation grille
Booster
Restrictaflow
Sink shown
only
ø50 hole
HydroTap®
AIO Tap
Position the Tap such that it
dispenses into the sink bowl
with ample clearance for a cup
or a tea pot.
193
211
48
234
333
461
SECTION A-A
SCALE 1 : 5
Clearance
Envelope
43
5
B. Cabinet Floor Cut-Out
4 min.
Buffer Pad
Clear Gap
See Detail B
Table - Zip BOM (Assembly)
Item Part Rev Description Config Status
Default/
Qty
Notes
1 1456AU A
HydroTap G4 Residential BCS Base Module Vented w/
Booster
1456AU Production 1
3 800221 C Air Inlet Grill CFF Default Production 1
8 27200 A Zip Hydrotap Booster MBX2 2.2kW 10A 230V Default Production 1
12 84451 A Tee 1/2" BSP Female (Brass) Default Production 1
18 802240 00 AIO Sparkling Tap G4 Assy (Vented) Default Design 1
21 800349 A 1.2kg CO2 Cylinder Assy Default Production 1
26 85193! A08 Assy - Restrict-A-Flow with ø2.5 Hole 87722 Prototype 1
27 83393 A14 Ventillation Grille Hafele Default
Pending Pre-
Production
1
150
50
200
250
150 100 50 250 200
50 100
250
200
100
150
Web : www.zipindustries.com
Email : [e-mail]
100
300
400
400
300
350
350
550 450 500 400 350 300
150 200 250 300 350
Dimensions in
millimetres
Drawing to
BS8888:2004
Screw threads to
BS 8498:2008
File Ref : C:\Zip_PDM\Engineering\Projects\Project 10002\2. Design\Residential HydroTap G4 BCS\KL002_1456AU0A6ZN1R (Sheet1)
Sheet1 (Default)
Zip Industries Pty Ltd
67 Allingham Street
Condell Park
Sydney
NSW 2200
Australia
No
Handed? :
edgarg on 4/08/2015
edgarg on 25/08/2016 3:17:15 PM
Updated by :
EdgarG on 4/05/2011
02
A2
Created by & on
Created by & on
Potable? : Recyclable? :
No No
Buy
Manufacturing Process
See Components
this was 1454AU0A6ZN1R. HT 1789 is now with 1456AU0A6ZN1R
Comments :
Remove all sharp edges. This drawing ONLY details information
which cannot be ascertained from the 3D geometry of the part(s)
attached. Model & dimensions are AFTER all finishing operations
Raw material :
Manufacturing Route :
Make or Buy :
This drawing is CONFIDENTIAL and is supplied on the express condition that it shall not be LOANED, COPIED or DISCLOSED to
any other third party or used for any purpose without the written consent of Zip Industries Pty Ltd. If this document is printed in
hardcopy form, it is for INFORMATION ONLY and therefore not subject to updating controls.
For the current revision ALWAYS refer to the NATIVE electronic form as stated in the top left-hand corner of this sheet.
© copyright Zip Industries Pty Ltd, 16/05/2011
Assy - Kitchen Layout (HydroTap G4 Residential
BCSHA Unit & AIO Tap Vented with Booster)
KL002_1456AU0A6ZN1R
92836.9
See Components
Sheet :
1
of
1 1:1
edgarg on 4/08/2015
EdgarG
on 16/05/2011
New
Manufacturing Instructions
Zip Industries
KL002_1456AU0A6ZN1R
Drawing :
Model :
Description :
Status :
Derived from :
Scale :
Approved by :
Checked by :
Finish
Finish :
Material :
Mass
(g)
:
Density
(g/cm3)
:
1.2
Area
(cm2)
:
139916.7 79597.4
Volume
(cm3)
:
Prototype
Default
Configuration :
Hydrotap G4®
Project :
Size
Rev
WMKA 00099; CS8328
Watermark Exp: 26-10-2017; CS Exp: 18-8-2014
Colourless
Colour :
_Drawing
Property
Config
Property
Custom
Property