Installation Guide

THIRD ANGLE
PROJECTION
R
Configuration : Default
126
46
338
105
400
209
50 min 50 min
333
200 min.
A
A
Mains cold water
isolation valve
(not supplied)
240 - 230V,
50Hz GPO
Clearance
Envelope
Inlet Vent
CO
2
gas
cylinder
Ventilation grille
35 Hole
for G4 Tap
Sink shown
only
104
219
6
308
116 CL reach
232
DETAIL FONT
SCALE 1 : 5
219
circumference
21
108 hole
for bowl
83
60
10 cut-away for
6mm fastening
stud
35 hole for
tap tubes
326
43 max.
5
B. Cabinet Floor Cut-Out
461
SECTION A-A
SCALE 1 : 5
Clearance
Envelope
4 min.
Buffer Pad
Clear Gap
See Detail B
Table - Zip BOM (Assembly)
Item Part Rev Description Config Status Qty Notes
1 800544-BCS 00
Tap Assy Commercial - Boiling Chilled
Sparkling HydroTap G4
Default Design 1
5 A2450 A Plug - Australian Standard Default Production 1
8 1254AU! A
HydroTap G4 Residential BCS Base
Module Mains/UnVented
Default Production 1
9 85193! B Assy - Restric-A-Flow with ø2.5 Hole
With One (1)
Nut
Production 1
10 802084 A04 "Y" Connector JG 1/4" Default Pre-Production 1
11 800221 C Air Inlet Grill CFF Default Production 1
12 800349 A 1.2kg CO2 Cylinder Assy Default Production 1
16 83393 A14 Ventillation Grille Hafele Default
Pending Pre-
Production
1
150
50
200
250
150 100 50 250 200
50 100
250
200
100
150
Web : www.zipindustries.com
Email : [e-mail]
100
300
400
400
300
350
350
550 450 500 400 350 300
150 200 250 300 350
Dimensions in
millimetres
Drawing to
BS8888:2004
Screw threads to
BS 8498:2008
File Ref : C:\Zip_PDM\Engineering\Projects\Project 10002\2. Design\Residential HydroTap G4 BCS\KL002_1256AU0S0ZN1R (Sheet1)
Sheet1 (Default)
Zip Industries Pty Ltd
67 Allingham Street
Condell Park
Sydney
NSW 2200
Australia
No
Handed? :
edgarg on 4/08/2015
edgarg on 25/08/2016 12:45:13 PM
Updated by :
EdgarG on 4/05/2011
02
A2
Created by & on
Created by & on
Potable? : Recyclable? :
No No
Buy
Manufacturing Process
See Components
Manufacturing Code was 1254AU0S0ZN1R
Comments :
Remove all sharp edges. This drawing ONLY details information
which cannot be ascertained from the 3D geometry of the part(s)
attached. Model & dimensions are AFTER all finishing operations
Raw material :
Manufacturing Route :
Make or Buy :
This drawing is CONFIDENTIAL and is supplied on the express condition that it shall not be LOANED, COPIED or DISCLOSED to
any other third party or used for any purpose without the written consent of Zip Industries Pty Ltd. If this document is printed in
hardcopy form, it is for INFORMATION ONLY and therefore not subject to updating controls.
For the current revision ALWAYS refer to the NATIVE electronic form as stated in the top left-hand corner of this sheet.
© copyright Zip Industries Pty Ltd, 16/05/2011
_Drawing
Property
Part
Property
Assy - Kitchen Layout (HydroTap G4 Residential
BCS Unit & G4 Tap) 58mm Wider
KL002_1256AU0S0ZN1R
87900.1
See Components
Sheet :
1
of
1 1:1
edgarg on 4/08/2015
EdgarG
on 16/05/2011
New
Manufacturing Instructions
Zip Industries
KL002_1256AU0S0ZN1R
Drawing :
Model :
Description :
Status :
Derived from :
Scale :
Approved by :
Checked by :
Finish
Finish :
Material :
Mass
(g)
:
Density
(g/cm3)
:
1.1
Area
(cm2)
:
132109.2 78578.0
Volume
(cm3)
:
Prototype
Default
Configuration :
Hydrotap G4®
Project :
Size
Rev
WMKA 00099; CS8328
Watermark Exp: 26-10-2017; CS Exp: 18-8-2014
Colourless
Colour :