ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL R ZINWELL ZINWELL ZINWELL Brite-View ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWE
Table of Contents Chapter 1 Introduction 1.1 Important Notices............................................................................................... 2 1.2 Product Functions.............................................................................................. 2 1.3 Package Contents.............................................................................................. 3 Chapter 2 Installation 2.1 Product Overview.........................................................................
Chapter 1 Introduction Thanks for your purchase of Zinwell Brite-View. With Brite-View, you can turn your existing standard video into a high quality picture on your display devices. The system set up is very easy and no additional hardware or software required. You don't need to learn a complicated set up procedure and you can enjoy your Brite-View with just plug and play. 1.1 Important Notices Please use the Brite-View under a normal environment 1. Try to avoid the following circumstances.
1.3 Package Contents As you unpack the Brite-View, please make sure the following items were included. If any of these items are missing, call your local agencies. 1. Brite-View ......................................................................................x1 2. Power supply ..................................................................................x1 3. Video cable......................................................................................x1 4. S-video cable.........................
Chapter 2 Installation 2.1 Product Overview 2.1.
2.1.2 Rear view of Brite-View RGB / Y Pb Pr OUTPUT RGB OUTPUT SELECT INPUT 7 6 5 4 Y Pb Pr 2 3 1 1 OUTPUT SOURCE SWITCH Please check your output device and switch YPbPr or RGB to select output signal. 2 VGA OUTPUT Please use the VGA OUTPUT to connect your progressively scanned TV or projector. 3 YCbCr INPUT Please connect the RCA cable to DVD player. 4 VIDEO INPUT Please connect the external video from VCR, LD, V8 or video game to the VIDEO INPUT of box.
2.2 System Installation : HDTV monitor Plasma HDTV monitor Projection TV Widescreen TV Projector RGB / Y Pb Pr OUTPUT INPUT Y Pb Pr RGB OUTPUT SELECT Progressive DVD DVD Composite S-VIDEO cable Camera Video game Adapter Warrning: please turn off the power of all devices before connection.
Chapter 3 Operation Instruction 3.1 Initial Setting When you finish the connections of Brite-View, please refer to the following instructions of IR control and start the system setting, because all the function settings are in the IR control. Steps: 1. Please install 2 AAA batteries into IR control. 2. Please refer to p6 for your configuration. 3. Turn on the power. 4. Press the "Video", "S-Video" or "YCbCr" on IR control button to select input signal Source. 5.
3.
3.3 PICTURE Setting The PICTURE setting are provided by hot key adjustment on remote controller. When you press the CONTRAST, BRIGHTNESS, SATURATION, HUE, and SHARPNESS buttons on remote controller, an adjustment bar shall show up on the middle down of display screen; to press "+" or "-" to adjust the value, and the bar shall disappear automatically after 5 seconds. BRIGHTNESS 80 3.4 PREFERENCE Setting 3.4.
3.4.2 ASPECT: to press ASPECT to select 4:3 or 16:9 This selection is available only for RGB mode output. 4:3 16:9 3.5 RESET: to press RESET to return all system settings (including PICTURE settings, ASPECT, RESOLUTION, INPUT source) to factory default value. When you press RESET button, all the previous personal settings shall be cleared. 3.6 INPUT source: to press Video (Composite Video), S-Video, or YCbCr, button to select input signal.
Chapter 4 Other Information 4.1 Troubleshooting Symptom No picture on display Solution Make sure the power cord is connected to an AC outlet, DC plug is connected to DC IN port and the power LED is on. Make sure the display's power is on. Check the connection of your source signal. To reset the Brite-View, unplug the DC IN adapter from the unit and then plug it back in again. Video distorted The remote control out of function Check all of the connection. Make sure batteries are installed.
4.2 Specifications POWER 100 ~ 240VAC 0.4A 50/60HZ - 12VDC 1.
ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWELL ZINWE
