Technical Specifications

Lower temperatures, higher humidity can prolong dry time. If
conditions do not permit prompt drying, allow PEEL STOP to dry
overnight before priming or painting. Do not apply PEEL STOP if
rain is expected and primer or topcoat cannot be applied before
rain occurs. Note: Product that has seeped under the edges of
remaining paint layers or has filled minute cracks may take
longer to dry than material on exposed surfaces.
Priming & Topcoating – Any quality water-base or oil-base
primer or paint may be used over PEEL STOP. Since PEEL STOP
is clear, it may be necessary to prime surfaces to achieve hide
using Bulls Eye
®
1-2-3 or Cover-Stain
®
followed by a coat of
quality latex or alkyd paint to assure optimum results.
Coverage – Approx. 400 sq. ft. (37 m
2
) per gallon on smoother
surfaces; 300 sq. ft. (28 m
2
) per gallon on rough, unpainted,
porous surfaces. Application losses may vary according to the
porosity of the substrate and the method of application and
should be taken into account when estimating the quantity of
product needed.
Cleanup – Clean up spills and drips with liquid detergent and
warm water. If spills or drips have dried use denatured alcohol
or ammoniated detergent to soften and remove primer. Wash
application tools in a solution of detergent and water
immediately after use. If dried on tools let soak overnight in a
solution of equal parts ammoniated detergent and water. Scrub
bristles clean with a wire brush. Follow manufacturer’s
instructions when cleaning spray equipment.
Disposal – Dispose of unused or unwanted product in
accordance with local laws regulating water-based coatings.
Limitations – PEEL STOP is formulated to help prolong the
adhesion of existing paint coatings and is not intended as a
substitute for proper surface preparation or for application to
surfaces where paint failure results from chronic or excessive
moisture intrusion. Repair any source of moisture intrusion
before attempting to repaint. Ongoing paint failure may require
complete removal of the existing coating system. Not for use on
floors, exterior decks or surfaces subject to immersion or
prolonged contact with water.
Warranty – PEEL STOP is guaranteed to perform as indicated
when applied according to label directions to a properly prepared
surface. Directions are as complete as possible but cannot
encompass all conditions, applications, and/or surfaces beyond
manufacturer’s control. The contents of the container are
warranted to be free from any other defect for 2 years from the
date of manufacture. All warrantees and guarantees are limited
to refund or replacement of product used with proof of
purchase. No other warranty or guarantee is expressed or
implied.
Typical Physical Properties
Percent Solids, Weight: 21.6%
Percent Solids, Volume: 19.3%
Density: 8.73 lb. (3.96 kg)/gal
Viscosity Range: 2000-4000 cps
Theoretical Spread Rate
@ 1 mill DFT: 417 sq. ft (xx m
2
)/gal
Dry Time @ 75
o
F/50% RH: Touch: 1 hour
Recoat: 2 hour2
Adhesion Cure @ 75
o
F/50% RH: 7 – 10 days
Flame Spread (ASTM-84-97A): 0, Class 1
Smoke Contrib. (ASTM-84-97A): 5, Class 1
Flash Point (ASTM D3278): >200
o
F (93
o
C)
VOC: 100 g/L
Freeze/Thaw Stable: Yes
Shelf Life: 60 mo @ 75
o
F (24
o
C)
Storage/Handling: Store indoors
40
o
– 90
o
F
(4
o
– 32
o
C)
Precautions - WARNING! Do Not Take Internally. May
cause gastrointestinal irritation. If swallowed call physician or
poison control center. Avoid contact with eyes and skin. May
cause eye and skin irritation. In case of eye contact flush eyes
with water for at least 15 minutes. Use with adequate
ventilation. Keep Out of Reach of Children.