MSDS

ManualsBrandsZinsser ManualsPaint18 oz. Power Stripper Spray (6-Pack)

Material Safety Data Sheet

N/A: Not Applicable N/D: Not Determined N/E: Not Established N/R: Not Required Est.: Estimated

Parks Power Stripper Aerosol MSDS (03-19-09) Page 1 of 7 pages.

Section 1 General Information

Manufacturer:

Rust-Oleum Corporation

11 Hawthorn Parkway

Vernon Hills, IL 60061

24 Hour Assistance: 1-847-367-7700

www.rustoleum.com Date: March 19, 2009

Product Name: Parks Power Stripper Aerosol

Codes: 42101

Section 2 Hazardous Ingredients

OSHA ACGIH

Hazardous Component

CAS#

PEL TLV

Methylene Chloride 75-09-2 25 ppm

125 ppm (STEL)

50 ppm

Dipropylene Glycol-Methyl Ether 34590-94-8 100 ppm 100 ppm

150 ppm (STEL)

Methanol 67-56-1 200 ppm 200 ppm

250 ppm (STEL)

Toluene 108-88-3 200 ppm

300 ppm (C)

50 ppm

Propane 74-98-6 1,000 ppm 1,000 ppm

Isobutane 75-28-5 N/E 1,000 ppm

C = Ceiling Value

Section 3 Hazard Identification

Emergency Overview: This product is an aerosol paint stripper. Contents under pressure.

Extremely flammable liquid and vapor. Vapors may ignite explosively. Vapors may cause flash fire.

May cause eye burns.

Primary Routes of Exposure:

Skin Contact

Eye Contact

Inhalation

Summary of content (7 pages)

PAGE 1
Material Safety Data Sheet Section 1 General Information Manufacturer: Rust-Oleum Corporation 11 Hawthorn Parkway Vernon Hills, IL 60061 24 Hour Assistance: 1-847-367-7700 www.rustoleum.
PAGE 2
Potential Acute Health Effects: Eye: Exposure may cause severe eye irritation and eye burns. Symptoms may include burning, stinging, tearing, and redness. Skin: Exposure to skin may cause skin irritation or a burning sensation. Prolonged or repeated contact may cause skin to become reddened, rough and dry due to the removal of natural oils and may result in dermatitis. May be harmful if absorbed through skin. May cause allergic skin reaction.
PAGE 3
Inhalation: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately. If breathing is difficult, have trained person administer oxygen. If breathing has stopped, give mouth-to-mouth resuscitation.
PAGE 4
such as pits or other poorly ventilated areas. Do not enter places where vapors are suspected. KEEP OUT OF REACH OF CHILDREN. Section 8 Exposure Controls / Personal Protection Engineering Controls: Use this product outdoors, if possible. If you must use it indoors, open all windows and doors or use other means to ensure fresh air movement during application and drying. Use only in well-ventilated areas. Do not use in basement or other unventilated area.
PAGE 5
Vapor Pressure: N /D Vapor Density: Heavier than air. Viscosity: Solubility in Water: Insoluble. N/D Specific Gravity (water = 1): > 1 Section 10 Stability and Reactivity Stability: Stable. Hazardous Polymerization: Will not occur. Hazardous Decomposition Products: Combustion may yield carbon monoxide and carbon dioxide. Conditions to Avoid: Open flames, welding arcs or other high temperature sources. Incompatibility: Avoid contact with oxidizers and reactive metals (i.e.
PAGE 6
Section 13 Disposal Considerations Recommended Waste Disposal Method: This material, when discarded or disposed of, could be a hazardous waste according to federal regulations (40 CFR 261) due to the characteristic of ignitability (D001). The transportation, storage, treatment, and disposal of this waste must be conducted in compliance with 40 CFR 262, 263, 264, 268, and 270. Disposal can only occur in properly permitted facilities.
PAGE 7
SARA Title III, section 313: The Superfund Amendments and Reauthorization Act of 1986 (SARA) Title III requires submission of annual reports of release of toxic chemicals that appear in 40 CFR 372 (for SARA 313). Components present in this product at a level which could require reporting under the statute are: Chemical Name Methylene Chloride Methanol CAS# 75-09-2 67-56-1 Maximum Concentration (Wt. %) 75.0 % 4.