Technical Specifications

ManualsBrandsZinsser ManualsWaterproofersWatertite Clear Gloss Waterproofer (Actual Net Contents: 1-gallon)

TECHNICAL DATA

WRT-11

ZINSSER

WATERTITE

CLEAR

MOLD & MILDEW PROOF FLOOR & WALL PAINT

Form: GDH-1077

Rev.: 012821

DESCRIPTION AND USES

Zinsser

WaterTite

Clear

Mold & Mildew-Proof Floor & Wall

Paint is a modified acrylic copolymer designed to form an

impermeable and very smooth, non-pigmented barrier to

water on bare masonry wall and floor surfaces. It is intended

for use on interior or exterior, vertical or horizontal, concrete

block (not lightweight block) and cast-in-place concrete. It

stops moisture from entering or exiting a concrete surface.

WaterTite

Clear Mold & Mildew-Proof Floor & Wall Paint

meets ASTM D-7088 Resistance to Hydrostatic Pressure

and ASTM D-6904 Resistance to Wind Driven Rain.

PRODUCT FEATURES

 Interior and Exterior

 Floor & Wall Application

 Clear, Smooth Finish

 For Concrete & Masonry

 Resists Wind-Driven Rain

 Gloss Formula

 Resist 10 PSI of Water Pressure

PRODUCT

SKU

DESCRIPTION

306607

1 Gallon

WHERE TO USE

For maximum performance, apply WaterTite Clear Mold &

Mildew-Proof Floor & Wall Paint over uncoated surfaces. It is

suitable for use on basement or cellar walls and floors to

stop moisture from entering. It also works well on retaining

walls and concrete subfloors. WaterTite

Clear Mold &

Mildew-Proof Floor & Wall Paint can be topcoated with latex,

oil-based or epoxy coatings. It is not recommended for use

on garage floors, in swimming pools or use in contact with

potable water. It can be applied over previously painted

surfaces; however, its waterproofing ability is dependent

upon the integrity and moisture resistance of the prior

coating.

PRODUCT APPLICATION

READ ALL INSTRUCTIONS CAREFULLY BEFORE

STARTING PROJECT

SURFACE PREPARATION

Surfaces must be clean, dry and sound, and free of dirt,

efflorescence, mold, algae, sandy mortar or any material that

could compromise coating adhesion. New concrete must be

cured for at least 7 days prior to coating. Splash water on the

surface to test for the presence of sealers or release agents.

PRODUCT APPLICATION (cont.)

SURFACE PREPARATION (cont.)

If the surface turns dark with the water,

WaterTite Clear Mold

& Mildew-Proof Floor & Wall Paint

can be applied.If not, the

surface must be chemically cleaned and retested before

proceeding. Wash, vacuum, scrape, wire brush or

mechanically abrade to clean the surface.

Remove efflorescence with WaterTite Etch and Cleaner

(sold separately) or equivalent product. Follow label

directions carefully and allow to dry completely. Wipe your

fingers over the clean, dry surface. If and dust or powder is

seen on your fingers, repeat scrubbing and rinsing until

clean. Wear chemical resistant splash goggles and a NIOSH

approved respirator and gloves while handling the etch.

Cast concrete, concrete block and mortar joints must be

hard and firm - not loose or sandy. Scrape the surface with a

flat screw driver using moderate pressure. If soft or sandy,

contact a professional contractor. Use mechanical means

(chip hammer, needle gun or abrasive blast) to open holes

(bug-holes) caused by air bubbles in cast-in-place concrete

to allow the coating to fully penetrate. Replace missing

mortar. Fill cracks and holes (⅛”) with WaterTite Hydraulic

Cement (sold separately) or equivalent product. Fill cracks

and expansion joints with WaterTite Polyurethane Sealant

(sold separately).

WARNING! If you scrape, sand or remove old paint, you

may release lead dust. LEAD IS TOXIC. EXPOSURE TO

LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS

BRAIN DAMAGE, ESPECIALLY IN CHILDREN.

PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.

Wear a NIOSH-Approved respirator to control lead

exposure. Clean up carefully with a HEPA vacuum and a wet

mop. Before you start, find out how to protect yourself and

your family by contacting the National Lead Information

Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

APPLICATION

Mix thoroughly before use. DO NOT THIN. Apply only when

air, material, and surfaces temperatures are between

50-90°F (10-32°C) and the relative humidity is or less than

85%. Use a brush or ¾” nap roller. It is important to work the

first coat into block pores. If using a roller, back brush the

first coat to work the coating into the concrete pores. Apply

two coats to form a continuous pin-hole free coating. A third

coat may be necessary depending on block porosity. FOR

MAXIMUM PROTECTION OF 10 LBS. WATER PRSSURE

RESITANCE, BRUSH IN THE FIRST COAT.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA WRT-11 ZINSSER® WATERTITE® CLEAR MOLD & MILDEW PROOF FLOOR & WALL PAINT DESCRIPTION AND USES PRODUCT APPLICATION (cont.) Zinsser® SURFACE PREPARATION (cont.) WaterTite® Clear Mold & Mildew-Proof Floor & Wall Paint is a modified acrylic copolymer designed to form an impermeable and very smooth, non-pigmented barrier to water on bare masonry wall and floor surfaces.
PAGE 2
TECHNICAL DATA WRT-11 ZINSSER® WATERTITE® CLEAR MOLD & MILDEW PROOF FLOOR & WALL PAINT PRODUCT APPLICATION (cont.) APPLICATION (cont.) The second coat can be brushed or rolled on. WaterTite Clear Mold & Mildew-Proof Floor & Wall Paint can be spray applied with an airless or conventional sprayer, but always back brush the first coat. For floor applications, the second coat should be applied in a cross direction to the first coat to achieve uniformity. Apply 2 coats.
PAGE 3
TECHNICAL DATA WRT-11 ZINSSER® WATERTITE® CLEAR MOLD & MILDEW PROOF FLOOR & WALL PAINT PHYSICAL PROPERTIES CLEAR MOLD & MILDEW-PROOF FLOOR & WALL PAINT Resin Type Acrylic Pigment Type None Solvents Glycol Ethers, Water Per Gallon 8.6 lbs. Per Liter 1.03 kg By Weight 30.0% By Volume 27.4% Weight Solids Volatile Organic Compounds 100 g/l (0.83 lbs./gal.) Recommended Dry Film Thickness (DFT) Per Coat 5.0-6.0 mils (125-150µ) Wet Film to Achieve DFT (unthinned material) 18.0-22.