SDS

Date Printed: 2/22/2019
6. Accidental Release Measures
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Contain spilled liquid with sand or earth. DO NOT use
combustible materials such as sawdust. Isolate the hazard area and deny entry to unnecessary and unprotected personnel. Remove
all sources of ignition, ventilate area and remove with inert absorbent and non-sparking tools. Dispose of according to local, state
(provincial) and federal regulations. Do not incinerate closed containers. Ventilate area, isolate spilled material, and remove with
inert absorbent. Dispose of contaminated absorbent, container, and unused contents in accordance with local, state, and federal
regulations.
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Wash hands before eating. Remove contaminated clothing and launder before reuse.
Use only with adequate ventilation. Follow all SDS and label precautions even after container is emptied because it may retain
product residues. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.
STORAGE: Store in a dry, well ventilated place. Keep container tightly closed when not in use. Keep containers tightly closed.
Isolate from heat, electrical equipment, sparks and open flame. Contents under pressure. Do not store above 120 ° F. Store large
quantities in buildings designed and protected for storage of flammable aerosols. Keep away from heat, sparks, flame and sources of
ignition. Avoid excess heat. Product should be stored in tightly sealed containers and protected from heat, moisture, and foreign
materials.
Advice on Safe Handling of Combustible Dust: Minimize dust generation and accumulation. Routine housekeeping should be
instituted to ensure that dusts do not accumulate on surfaces. Dry powders can build static electricity charges when subjected to the
friction of transfer and mixing operations. Provide adequate precautions such as grounding and bonding or inert atmospheres. For
safe handling, refer to NFPA 654, Standard for the Prevention of Fire and Dust Explosions from the Manufacturing, Processing, and
Handling of Combustible Particulate Solids.
8. Exposure Controls / Personal Protection
Chemical Name CAS-No.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-TWA
OSHA PEL-
CEILING
Ethanol 64-17-5 35.0 N.E. 1000 ppm 1000 ppm N.E.
Acetone 67-64-1 30.0 250 ppm 500 ppm 1000 ppm N.E.
Liquefied Petroleum Gas 68476-86-8 25.0 N.E. N.E. N.E. N.E.
Shellac 9000-59-3 15.0 N.E. N.E. N.E. N.E.
2-Propanol 67-63-0 5.0 200 ppm 400 ppm 400 ppm N.E.
n-Butanol 71-36-3 5.0 20 ppm N.E. 100 ppm N.E.
Methyl Isobutyl Ketone 108-10-1 1.0 20 ppm 75 ppm 100 ppm N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Use explosion-proof ventilation equipment. Provide general dilution of local exhaust
ventilation in volume and pattern to keep TLV of hazardous ingredients below acceptable limits. Prevent build-up of vapors by
opening all doors and windows to achieve cross-ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use. A NIOSH/MSHA approved air purifying respirator with organic
vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed
exposure limits.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
Engineering Measures for Combustible Dust: It is recommended that all dust control equipment such as local exhaust ventilation and
material transport systems involved in handling of the product contain explosion relief vents, an explosion suppression system, or an
oxygen deficient environment. Ensure that dust handling systems such as exhaust ducts, dust collectors, vessels, and processing
equipment are designed in a manner to prevent the escape of dust into the work area (i.e., there is no leakage from the equipment).
Use only appropriately classified electrical equipment and powered industrial trucks.
Page 3 / 6