Technical Specifications

Sprayer: May be spray applied using conventional, HVLP, or
airless systems. Use a .011 to .013 tip and 800 to 1000 psi for
airless spray application. Follow equipment manufacturer’s
instructions.
Coverage – Approximately 400 to 600 ft
2
(37-55 m
2
) per
gallon. Spread rate may vary depending upon surface porosity
and method of application.
Application Directions
Doors/Trim/Paneling/Cabinets/Furniture - Apply 1 or more
coats by wiping, brush, or spray. Allow to dry completely
before sanding with 220 or finer grit between coats to ensure a
smooth finish. If a heavier film build is desired, repeat
application. Remove dust and apply finish.
Floors – Floors should be properly sanded and free of dust,
dirt, or other contaminants. Use a brush or floor finish
applicator and apply in the direction of the grain. Coat two or
three board widths at a time, being sure to keep a wet edge.
Avoid over-applying or over-brushing. Let dry for 1 hour before
sanding with 220 or finer sandpaper or screening. Apply
second coat and let dry 2 to 3 hours. Note that shellac is not
as durable or scratch-resistant as polyurethane or other
finishes formulated for application to floor surfaces.
Application Conditions
Warmer temperatures will accelerate and colder temperatures
will prolong the dry time of this product. Do not apply when RH
is greater than 85% or when temperature is within 10º of the
dew point. Bulls Eye Shellac is not recommended for use in
areas where surface heat exceeds 160
o
F (71
o
C). (Note – If in
doubt, always test apply shellac on scrap wood before using).
Dry time – At 70
o
F (21
o
C) the first coat on bare wood will
usually dry to touch in a few minutes and can be sanded and
recoated in about 20 to 30 minutes. Subsequent coats or coats
applied over existing finishes will dry to the touch in 10 to 15
minutes and can be sanded and recoated in about an hour.
Clean up – Wipe up drips and spills with a rag soaked in
denatured alcohol or use a solution of household ammonia and
water. Clean natural bristle brushes with denatured alcohol
and synthetic bristle brushes with a solution of 1 part sudsy
ammonia and two parts water.
To dissolve product that has dried on application tools, soak
tools overnight in ammonia solution or alcohol. Clean sprayer
equipment according to manufacturer’s directions
Typical Physical Properties (3-lb. cut)
Solids by weight 29%
Solids by volume 21%
Density 0.89
Viscosity range <200 cps
Max. VOC 730 g./liter
Flashpoint (Seta flash) 60
o
F (16
o
C)
Dry time (recoat)
@70
o
F (21
o
C) & 50% RH 20 to 45 minutes
Shelf Life @ 75
o
F. (24
o
C) 36 months
Storage/Handling 40
o
– 80
o
F (4
o
– 27
o
C)
Freshness Note and Warranty
This product is formulated to maintain rapid dry time and
maximum film hardness for 3 years after the manufacture date
stamped on the container bottom. After that time check for
proper drying by brushing on a piece of scrap wood. If surface
is not dry tack free within 2 hours do not use. Higher storage
temperatures may shorten shelf life. Do not expose to storage
temperatures > 95º F for extended periods of time. Bulls Eye
Shellac will perform as claimed if directions are followed.
Directions are as complete as possible, but cannot encompass
all conditions, applications, techniques and/or surfaces that are
beyond our control. If you have a question, check with your
dealer or contact ZINSSER Co., Inc. Somerset, NJ. Warranty is
limited to replacement or refund value of product actually used
if such product proves defective within two years of
manufacture.
Precautions
CAUTION: FLAMMABLE. Contains alcohol. Keep away from
heat, sparks, and flame. Use only with adequate ventilation.
Avoid prolonged breathing of vapor or extended skin contact. If
spraying, use explosion-proof equipment and wear a NIOSH
approved respirator. Do not take internally. KEEP AWAY
FROM CHILDREN. STORE AWAY FROM HEAT.