User manual

ManualsBrandsZiLOG ManualsComputer equipmentZ8F04A08100KIT

ZiLOG Worldwide Headquarters • 532 Race Street • San Jose, CA 95126

Telephone: 408.558.8500 • Fax: 408.558.8300 • www.zilog.com

Introduction

This Quick Start Guide describes how to set up your Z8 Encore! XP

Development Kit

and start using it to build designs and applications.

Kit Contents

Hardware

•

One of the following:

–

Z8 Encore! XP

4K Series Development Board

–

Z8 Encore! XP

4K Series 8-Pin Development Board

–

Z8 Encore! XP

F08xA Series Development Board

•

Smart Cable for PC to Z8 Encore!

Development Board (DB9 to six-pin male)

•

(Z8F04A08100KIT development kits only) USB Smart Cable for PC to Z8 Encore!

Development Board and driver CD-ROM

•

Universal 5V power supply

Software (on CD-ROM)

•

ZDS II–Z8 Encore!

IDE with ANSI C-Compiler

•

Sample code

•

Acrobat Reader install program

•

Document browser

Documentation

•

Registration Card

•

Z8 Encore! technical documentation (on CD-ROM)

–

Development Kit User Manual

–

ZDS II–IDE User Manual

–

eZ8 CPU User Manual

–

Product Specification

Z8 Encore! XP

Family of

Microcontrollers

Development Kits

QS004303-0205

Quick Start Guide

Summary of content (9 pages)

PAGE 1
Z8 Encore! XP® Family of Microcontrollers Development Kits QS004303-0205 Quick Start Guide Introduction This Quick Start Guide describes how to set up your Z8 Encore! XP® Development Kit and start using it to build designs and applications.
PAGE 2
Z8 Encore! XP® Development Kits Quick Start Guide Page 2 – – – – Product Brief Application notes Flyers Product Line Card Requirements Table 1 lists the system requirements for running ZDS II. Table 1.
PAGE 3
Z8 Encore! XP® Development Kits Quick Start Guide Page 3 this kit, refer to the Z8F04A08100KIT Z8 Encore! XP™ 4K Series User Manual, UM0187. Note: Steps 3 and 4 below refer to installing the serial Z8 Encore! Smart Cable. For instructions on installing the Z8 Encore! USB Smart Cable, refer to the USB Smart Cable User Manual, UM0181, on the CD-ROM included with the development kit.
PAGE 4
Z8 Encore! XP® Development Kits Quick Start Guide Page 4 Serial Smart Cable Serial Port Host PC To Electrical Outlet P2 Adapter Slot Development Board AC Cord Receptacle J1 Universal Power Supply Figure 1.
PAGE 5
Z8 Encore! XP® Development Kits Quick Start Guide Page 5 4. Select Yes to accept the agreement and proceed with the installation. 5. After selecting Yes, the Choose Destination Location screen appears. Follow the directions on the screen and choose whether to install ZDS II in the default location or in some other folder. Click Next. Unless you select a different location, the software is installed in: C:\Program Files\ZiLOG\ZDSII_Z8Encore_\ 6. The Select Program folder screen appears.
PAGE 6
Z8 Encore! XP® Development Kits Quick Start Guide Page 6 5. Browse to the Samples folder, located by default in: c:\Program Files\ZiLOG\ZDSII_Z8Encore_\Samples\ 6. In the Samples folder, select the Z8Fxxxx_ledBlink folder, then the src folder, to access the ledBlink.zdsproj project file. Note: The sample used in the following steps is in the C programming language. An assembler version of the ledBlink sample is located in the Z8Fxxxx_ledBlink_asm folder. 7. Select the ledblink.
PAGE 7
Z8 Encore! XP® Development Kits Quick Start Guide Page 7 8. Click the Rebuild All icon to build the project. Wait for the build to complete. 9. Click the Reset icon to connect and download the code to the development board. 10. Click Go to start the program. The screen changes as illustrated in Figure 3 on page 7. Rebuild All Icon Reset Icon Go Icon Figure 3.
PAGE 8
Z8 Encore! XP® Development Kits Quick Start Guide Page 8 11. The three LEDs on the development board begin blinking in sequence. If the LEDs do not blink, start over from Step 3 on page 5. Note: (Z8F04A08100KIT development kits only) LED D2/PA0 is shared with the DBG pin when the board is in debug mode. The LED will therefore not be fully illuminated. 12. Press the TEST pushbutton to change the sequence of the LEDs to blink in the opposite direction.
PAGE 9
Z8 Encore! XP® Development Kits Quick Start Guide Page 9 This publication is subject to replacement by a later edition. To determine whether a later edition exists, or to request copies of publications, contact: ZiLOG Worldwide Headquarters 532 Race Street San Jose, CA 95126 Telephone: 408.558.8500 Fax: 408.558.8300 www.ZiLOG.com Document Disclaimer ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries.