USB Smart Cable User Manual UM018112-0908 Copyright ©2008 by Zilog®, Inc. All rights reserved. www.zilog.
USB Smart Cable User Manual ii Revision History Each instance in the Revision History table reflects a change to this document from its previous revision. Date Revision Level Description September 12 2008 Updated Connecting to the Target Board April 2008 2 and 3 Updated USB Smart Cable Firmware Compatibility.
USB Smart Cable User Manual iii Table of Contents USB Smart Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supported Host Environments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the USB Smart Cable and Driver . . . . . . . . . . . . . . . . . . . Windows Vista-32/64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Windows XP .
USB Smart Cable User Manual 1 USB Smart Cable Zilog’s USB Smart Cable, ZUSBSC0100ZACG, allows you to connect ZLF645, Z8 Encore!®, Z8 Encore! XP®, ZNEO®, or eZ80Acclaim!® development board to a high-speed or full-speed USB port on Zilog Developer Studio II (ZDS II) host system. This user manual provides instructions for installing USB Smart Cable hardware and the associated drivers.
USB Smart Cable User Manual 2 The USB Smart Cable cannot operate properly on an unpowered Hub (that is, a Hub without a separate AC adapter). Note: Windows NT hosts are not supported by the USB Smart Cable. Table 1. Supported Target Environments Development Board System Clock Power Supply Minimum Maximum Minimum Maximum Encore!®, Current Z8 32 kHz Z8 Encore! XP®, ZLF645 20 MHz 2.7 V 3.6 V 2 mA ZNEO® 10 kHz 20 MHz 2.7 V 3.6 V 2 mA 5 MHz 50 MHz 3.0 V 3.
USB Smart Cable User Manual 3 Installing the USB Smart Cable and Driver Before connecting the USB Smart Cable to your system, Windows loads the appropriate driver from the ZDS II installation directory or CD-ROM. You can download ZDS II software for a specific device family at www.zilog.com. Alternatively, if you have an applicable Zilog development tool, use the CD-ROM provided. The installation procedure depends on your Windows operating system version.
USB Smart Cable User Manual 4 The Windows Security dialog box is displayed. 6. Select Install this driver software anyway. 7. When the software has been installed, click Closed. Windows XP 1. Connect the USB Smart Cable to the host PC for the first time. The Found New Hardware Wizard should activate automatically. 2. In the Wizard, select Install from a list or specific location (Advanced); then click Next. Note: If the Windows Logo testing dialog appears, select Continue Anyway. 3.
USB Smart Cable User Manual 5 4. Select Specify a location; then click Next. 5. Browse to one of the following driver directory: \device drivers\USB\x32 \Device Drivers\USB\x32 6. Click OK, and then click Next after the appropriate driver is found. 7. Click Finish to complete the installation. Windows 98 SE 1. Connect the USB Smart Cable to the host PC. The Found New Hardware Wizard should activate automatically. 2.
USB Smart Cable User Manual 6 Connecting to the Target Board Power-On Sequence Follow the steps below before connecting to target: 1. Connect the USB Smart Cable to the Host PC. 2. Connect the USB Smart Cable six-pin connector to the target board. 3. Apply power to the target board. If the target is not connected properly, remove the USB Smart Cable from the host PC and repeat the above steps. If the connection issues are still there, see Troubleshooting Tips on page 7.
USB Smart Cable User Manual 7 Troubleshooting Tips If a hardware failure is suspected, contact a local Zilog representative for assistance. Before submitting a problem report to Zilog Customer Support, follow the instructions in this section. USB Smart Cable Not Recognized Disconnect all other USB devices (including keyboard and mouse if you can use PS2 ports instead). Ensure that USB Smart Cable is plugged in directly with no intervening Hub.
USB Smart Cable User Manual 8 Customer Support For answers to technical questions about the product, documentation, or any other issues with Zilog’s offerings, visit Zilog’s Knowledge Base at http://www.zilog.com/kb. For any comments, detail technical questions, or reporting problems, visit Zilog’s Technical Support at http://support.zilog.com.
USB Smart Cable User Manual 9 Warning: DO NOT USE IN LIFE SUPPORT LIFE SUPPORT POLICY ZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
