CS4070 Scanner Quick Reference Guide
CS4070 Scanner No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis.
Quick Reference Guide 3 Introduction The CS4070 Scanner captures and stores bar codes for a variety of uses, and transmits bar code data to a host via USB connection or Bluetooth. This document provides basic instructions for setting up, programming, and using CS4070 scanners. The scanner is available in the following configurations: • CS4070SR - Standard range, cordless Bluetooth • CS4070HC - Healthcare, cordless Bluetooth Each scanner includes a micro USB host cable.
CS4070 Scanner Charging Before using the CS4070 for the first time, charge the battery using the micro USB cable or a cradle until all four green charging LEDs light. Charge time is approximately three hours for a fully discharged battery. Inserting the Battery 1. Insert the battery, bottom first, into the battery compartment in the back of the device. Ensure the charging contacts point toward the bottom of the scanner. 2.
Quick Reference Guide 5 Charging via USB Host Cable 1. Insert the micro USB connector on the cable in the interface port on the scanner. 2. Connect the other end of the host cable to a USB port on the host PC, or to a USB power adapter plugged into an AC outlet.
CS4070 Scanner Charging via Charging Cradle 1. Connect the single-slot or 8-slot charging cradle to power. 2. Insert the CS4070 into a device slot to begin charging. The CS4070 begins charging. The charge status LEDs light to indicate progress. See User Indications on page 14 for charging indications. Refer to the CS4070 Scanner Product Reference Guide for information on accessories.
Quick Reference Guide 7 Charging Spare Batteries 1. Connect the single-slot cradle or 8-slot spare battery charger to power. 2. Insert the battery into a spare battery slot with the charging contacts facing down, contacting the charging pins in the cradle. The charge LED on the cradle lights to show the charge status. Connecting to a Host Batch Connection The micro USB cable enables communication between the CS4070 and a PC, and charges the battery in the CS4070.
CS4070 Scanner Bluetooth Connection Pairing The CS4070 supports Serial Port Profile (SPP) and Human Interface Device (HID) protocols. To pair to a Bluetooth-enabled host: 1. Press the scan button (+) to wake the scanner. 2. Press and hold the Bluetooth button until the scanner beeps and the blue LED begins to flash to indicate that the scanner is discoverable by the host. 3. On the host, launch the Bluetooth pairing application and place the application into discover Bluetooth device mode.
Quick Reference Guide 9 Pairing via the Dongle To use the dongle accessory to pair to a USB HID device: 1. Connect the RJ45 cable to the dongle RJ45 port, and the other end of the cable to a USB port on the HID device. 2. Press the scan button (+) to wake the scanner. 3. Scan the bar code on the dongle to pair the scanner with the HID device. Unpairing To unpair the scanner and host, press the Bluetooth button. Upon unpairing, the Bluetooth button stops blinking.
CS4070 Scanner PIN Entry Bar Codes 0 1 2 3 4 5
Quick Reference Guide 6 7 8 9 Enter 11
CS4070 Scanner Bluetooth Communication Options To set up the scanner for communication with a host using a standard Bluetooth profile, scan one of the following bar codes. • Bluetooth HID Profile (default): The scanner emulates a keyboard. • Bluetooth Serial Port Profile (SPP): The scanner emulates a serial connection. • Bluetooth SSI Profile: The scanner uses SSI.
Quick Reference Guide 13 Scanning To scan a bar code: 1. Aim the scanner at the bar code. 2. Press the scan (+) button. 3. Ensure the aiming dot is centered on the bar code. The scanner beeps and the LED turns green to indicate a successful decode. See User Indications for beeper and LED definitions. Note The scanner cannot scan bar codes when it is connected to the host via the USB cable. Note Hold down the + button for 10 seconds to toggle the beeper functionality on and off.
CS4070 Scanner Deleting Bar Codes In batch mode, to delete a bar code aim the scanner at the bar code and press the delete ( - ) button. Note Bar codes cannot be deleted in Bluetooth mode.
Quick Reference Guide 15 Function User Action USB connection to host Connect scanner to host Flashing amber charging; solid green charged Low high Data protection toggle (when enabled) Hold both scan (+) and delete (-) buttons for 6 seconds None -> solid amber Short long short Bluetooth radio enable (discoverable) Hold Bluetooth button Rapidly flashing blue LED Short beep LED Beeper Bluetooth radio paired Slowly flashing Short low blue LED high Bluetooth radio out of host range Blue LED
CS4070 Scanner Transmitting Bar Code Data to Host Transferring Data via USB Cable The BarcodeFile.txt file within the \Scanned Barcodes directory on the scanner stores scanned (batch) bar code data. Connect the scanner to the host via USB cable or the charging cradle and use Windows Explorer to navigate to the scanner. Copy the bar code data file to the host. Note The scanner also supports an autorun feature where you can build an autorun.inf file to automatically copy data to the host upon connection.
Quick Reference Guide 17 Troubleshooting Problem Imager comes on, but scanner does not decode the bar code. Possible Solutions Ensure the scanner is programmed to read the type of bar code being scanned. Ensure the symbol is not defaced. Scan other bar codes of the same bar code type. Move scanner closer to or further from bar code. Scanner LED turns solid red for a few seconds. Charge the battery. See Charging on page 4. Scanner does not fully charge.
CS4070 Scanner Configuring the CS4070 123Scan2 Use the 123Scan2 utility to generate a 2D bar code with the desired configuration options. Scan the bar code to configure the scanner with these options. Config.ini Use a text editor such as Notepad to set configuration values in the Config.ini editable text file in the \Parameters folder on the CS4070. Updating Scanner Firmware 1. Connect the micro USB cable from the host to the CS4070. 2. Copy the .dat and .
Quick Reference Guide 19 Regulatory Information This guide applies to Model Number CS4070. All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following website: http://www.zebra.com/support Any changes or modifications to Zebra Technologies equipment, not expressly approved by Zebra Technologies, could void the user's authority to operate the equipment.
CS4070 Scanner Health and Safety Recommendations Ergonomic Recommendations Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.
Quick Reference Guide 21 Persons with Pacemakers: • Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON. • Should not carry the device in a breast pocket. • Should use the ear furthest from the pacemaker to minimize the potential for interference. • If you have any reason to suspect that interference is taking place, turn OFF your device.
CS4070 Scanner Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.
Quick Reference Guide 23 However, there are limitations to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe drops. When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur.
• • • • • • CS4070 Scanner Battery usage by children should be supervised. Please follow local regulations to promptly dispose of used re-chargeable batteries. Do not dispose of batteries in fire. Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
Quick Reference Guide 25 Radio Frequency Interference Requirements- Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada license-exempt RSS standard(s).
CS4070 Scanner Korea Warning Statement for Class B ITE 기종별 사용자안내문 B 급 기기 ( 가정용 방송통신 기자재 ) 이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며 , 모든 지역 에서 사용할 수 있습니다 . Other Countries Brazil (UNWANTED EMISSIONS - ALL PRODUCTS) Regulatory declarations for CS4070 - BRAZIL For more information consult the website www.anatel.gov.br Declarações Regulamentares para CS4070 - Brazil Nota: A marca de certificação se aplica ao Transceptor, modelo CS4070.
Quick Reference Guide 27 China 通过访问以下网址可下载当地语言支持的产品说明书 http://www.zebra.com/contact Mexico Restrict Frequency Range to: 2.450 – 2.4835 GHz. La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. S. Korea For a radio equipment using 2400~2483.
CS4070 Scanner Ukraine Дане обладнання відповідає вимогам технічного регламенту №1057, № 2008 на обмеження щодо використання деяких небезпечних речовин в електричних та електронних пристроях. Thailand เครื่ องโทรคมนาคมและอุปกรณ์น้ ี มีความสอดคล้องตามข้อกําหนดของ กทช. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: http://www.zebra.com/weee.
Quick Reference Guide 29 Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.zebra.com/weee. Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite: http://www.zebra.
CS4070 Scanner Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin: http://www.zebra.com/weee.
Quick Reference Guide 31
Service Information If you have a problem using the equipment, contact your facility’s technical or systems support. If there is a problem with the equipment, they will contact the Zebra Global Customer Support Center at: http://www.zebra.com/support For the latest version of this guide go to: http://www.zebra.com/support Warranty For the complete Zebra hardware product warranty statement, go to: http://www.zebra.com/warranty.
