HDMI/VGA Auto-switching wall plate HDBaseT transmitter over single CAT5e/6/7 100m, IEEE POE Powered, 4K, Audio, IR, RS232, LAN - WebOS ZIG-POEWP-100 USER MANUAL Ver. 1.0 zigencorp.
Table of Contents Copyright and Trademark Introduction Package Contents Features Specifications Panel Description – Front Side Panel Description – Back Side Connection and Installation Initial Connections Remote Control WebOS Interface RS-232 Commands Warranty 2 ZIG-‐POEWP-‐100 USER MANUAL 3 4 4 4 5 7 9 11 12 13 14 17 20
Copyright and Trademarks: All rights reserved by ZIGEN, INC. No part of this document may be reproduced in any form or by any means without written permission from the product manufacturer. Changes are periodically made to the information in this document. They will be incorporated in subsequent editions. The product manufacturer may make improvements and /or changes in the product described in this document at any time.
Introduction The ZIG-POEWP-100 is a wall plate 100 meter (328 feet) HDBaseT transmitter. It can be powered with a 5 VDC supply or from a POE RX device that it is connected to like a ZIG-PS-61 or ZIG-POE-RXAV. It can be used stand-alone as an HDBaseT wall-plate transmitter, but really shines when paired with the ZIGPOE-RXAV receiver/scaler & audio amplifier.
Specifications Ports Inputs HDMI x 1 VGA x 1 – multi-port – supports YPbPr, Y/C and C 3.5mm Audio port – follows VGA port Power – On back – 5VDC direct or IEEE POE from RX or switch Outputs HDBasetT x 1 – RJ45 Control/Access Via RJ45 and WebOS for direct control. Can also be accesses and controlled via ZIG-POE-RXAV or ZIG-PS-61 Distance between TX and RX Full HDBaseT - 328’ or 100M @ 2160P60 4:2:0 8-bit Copy Protection Compliance HDCP – Yes – 1.4 Video Bandwidth 10.
Audio Up to Dolby TrueHD and DTS Master Audio Wall Mountable Yes – 2 gang Decora style Color Black or White Power Consumption Less than 5W Dimensions 5.9 x 2.9 x .95 inches 150 x 74 x 24 millimeters Weight .67 pounds 303 grams Certifications/Compliance FCC, HDBaseT, CE, RoHS, HDCP, HDMI Works With Any properly implemented HDBaseT receiver or switch.
Front Side. See items 1-5 on next few pages zigencorp.
Panel Description Front Side 1. Source select – turns blue when HDMI is selected and off when VGA is selected. Source selection can happen 4 ways: a. b. c. d. Last source connected automatically is active and sent to display. By pushing this button the source will toggle. Via WebOS that will be covered later. Via 3rd party control. 2. HDMI Input – Connect HDMI cable here from your source (BlueRay, Computer, etc.) up to 4K UHD. 3.
Rear Side. See items 1-6 on next few pages zigencorp.
Rear Side 1. HDBaseT output/LAN Port (fallback) connection – Connect RJ45 up to 100 meters (328 feet) CAT5e, 6, 6a. This is the connection to an HDBaseT receiver such as the ZIG-POE-RXAV or ZIG-PS-61. You can also use this connection when accessing via WebOS. 2. 5 VDC Power connection – if NOT using POE power you can connect a 5VDC supply via phoenix style connectors. Captive Screw Connector – pin outs are also located on the unit.
zigencorp.
General – In the example above we are showing using an HDBaseT transmitter (ZIG-POEWP-100) connected to the HDBaseT receiver (ZIG-POE-RXAV) – as mentioned previously you also get an amplified audio output for direct connection to speakers, LAN ports for almost anything you choose and for controlling/setting up the devices, relays, a 4K scaler and IR and RS232 control and functionality. 1. Connect sources to POEWP – HDMI and VGA w/Audio 2. Connect RXAV to Display via HDMI 3.
ZIG-RXAV-POE Remote Control (comes with ZIG-POE-RXAV) Perfect for classrooms when connected to the ZIG-POEWP-100 use the remote to change between HDMI and VGA sources. • • • • Trigger devices connected to relays Mute the audio Power down the RXAV Control the Volume zigencorp.
WebOS Interface Page Status Device Name/Notes Control/ Defaults Firmware/Res et/ Info 14 ZIG-‐POEWP-‐100 USER MANUAL
WebOS Status Connections • • • HDMI – Green when HDMI is the source VGA – Green when VGA is the source Audio – Green when audio is present with the VGA signal Local HDBaseT (RXAV in this case) • • • • Link – Green when there is an HDBaseT connection HDMI - Green when HDMI is present Mode: Solid green when HDCP is present, flashing green when no HDCP detected.
Device Name & Notes • • Device Name – default out of the box is ZIG-POEWP-100.XXXX (last 4 digits of the serial number). You should change it if you are using more than 1 device (Change Name below) to whatever you want – ex. CR100RX – for conference room number 100 receiver. Notes – free form field for entering installer notes.
• Install Update – when necessary is for installing new software updates to the unit.
Decrease volume @rxav-01 voldn Decrease device ‘rxav-01’ volume by 1dB Response: @rxav-01 vol x Bass level [range -10dB to +10dB in 2dB steps] @rxav-01 bass 6 Set device ‘rxav-01’ bass level to +6dB Response: @rxav-01 bass x Treble level [range -10dB to +10dB in 2dB steps] @rxav-01 treb -2 Set device ‘rxav-01’ treb level to -2dB Response: @rxav-01 treb x Mute on/off @rxav-01 mute on Set device ‘rxav-01’ mute on Response: @rxav-01 mute x Relay 1 on/off @rxav-01 rel1 on Set device ‘rxav-
Display Device Info @rxav-01 man Get device ‘rxav-01’ device information Response: @rxav-01 Zigen Corp, ZIGPOE-RXAV, fw1 ver xx, fw2 ver yy Power on/off @rxav-01 pwr off Set device ‘rxav-01’ power off Response: @rxav-01 pwr x ZIG-POEWP-100 COMMANDS: Source switching (HDMI or VGA) @poewp-xxxx insel hdmi @poewp-xxxx insel vga zigencorp.
Warranty Information LIMITED WARRANTY – with the exceptions noted in the next paragraph, ZIGEN warrants the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of one year from the date of purchase. The proof of sale is required in order to claim warranty.
