Zigen HDBaseT Receiver (330 ft.), POE, 4K UHD Scaler, 20W per channel Amplifier, Ethernet ports, Relays, IR and RS-232 ZIG-POE-RXAV USER MANUAL Ver. 1.0 zigencorp.
Table of Contents Copyright and Trademark Introduction Package Contents Features Specifications Panel Description – Right Side Panel Description – Left Side Captive Screw Connections Connection and Installation Initial Connections Remote Control WebOS Interface RS-232 Commands Warranty 2 ZIG-‐POE-‐RXAV USER MANUAL 3 4 4 4 5 7 10 12 14 15 16 17 20 23
Copyright and Trademarks: All rights reserved by ZIGEN, INC. No part of this document may be reproduced in any form or by any means without written permission from the product manufacturer. Changes are periodically made to the information in this document. They will be incorporated in subsequent editions. The product manufacturer may make improvements and /or changes in the product described in this document at any time.
Introduction HDBaseT 328’/100M Receiver (RX) perfect for classrooms, boardrooms, huddle rooms and more – POE, 4K UHD and 4K UHD scaler, built-in amplifier that strips from HDMI, 2 Ethernet ports, 2 relays, WebOS. Also includes IR and RS232. Package Contents • • • • • • 1 x ZIG-POE-RXAV 1 x 24V/2.
Specifications Ports Inputs HDBaseT – RJ-45 Outputs HDMI x 1 L/R Audio (stereo) – via 4 pin female locking connector (Phoenix), 20W per channel Class D Control/Access IR in/out – 3.
Audio Stereo, 20W per channel RMS, Class D Amplifier 4K UHD Scaler Scales 1080P24/30 (generally a movie) incoming signal up to 2160P24/30 Wall Mountable Yes Power Consumption Depends on POE requirements. Without POE ~ 5W. With POE > 5W up to around 13W -> ~18W Dimensions 5.9 x 2.9 x .95 inches 150 x 74 x 24 millimeters Weight .67 pounds 303 grams Certifications/Compliance FCC, HDBaseT, CE, RoHS, HDCP, HDMI Works With Any properly implemented HDBaseT transmitter.
Right Side Panel. See items 1-6 on next few pages zigencorp.
Panel Description Right Side Panel 1. Speaker connection – 4 pin female locking connector. Connect directly to speaker wires and then to speakers. Output is 20 watts per channel – plenty or sound for classroom, bedroom, conference room or huddle room. 2. Dip Switch – Dip Switch Settings: Default/Factory – All Up or OFF Up = Off Down = On DIP 1: EDID OFF: EDID default mode (use EDID from connected TV) ON: Custom EDID - not implemented yet.
5. IR Receiver – built in IR receiver sensor – if possible place in line of site to remote control. You can also use 3.5mm or locking connections for IR receiver 6. Status Indicator Lights: a. Power – Solid green – indicated power is present b. Mode – Should be flashing green – data is flowing c. Link – Should be solid when TX and RX are connected d. HDCP – Solid Green – when HDCP is detected/present zigencorp.
Left Side Panel.
Left Side Panel 1. 2 LAN Connections/Full Duplex Ethernet ports. 10/100 BaseT. Use for programming the ZIG-POE-RXAV and ZIG-POEWP-100 or for 3rd party controller, or connection to your ISP or router. 2. IR connection terminal – 5-pin locking (Phoenix style) connector. a. IR OUT + b. IR OUT – c. Ground d. + 12V e. IR IN 3-12V 3. IR connection via 3.5mm a. IR OUT – Use mono plug tip & ring (P+ and P-) b.
Captive Screw Connectors – pin outs are also located on the top of the unit 2-pin connector – for power • • Power – connect black wire to negative terminal (-) Power – connect white wire to positive terminal (+) 3-pin connector – for relays • Relays – there are settings for both NO and NC for each relay – control via WebOS or 3rd party controller.
4-pin connector – for connecting to speakers • • • • • • Right Speaker + Right Speaker – Left Speaker + Right Speaker – 14 gauge and higher speaker wire pin outs are labeled on unit. 5-Pin connector – for IR connecting block • • • • • IR OUT + IR OUT – Ground + 12V IR IN 3-12V Note: connections also labeled on top of unit. Consult you IR device manufacturer for proper connections. zigencorp.
14 ZIG-‐POE-‐RXAV USER MANUAL
General – In the example above we are showing using an HDBaseT transmitter (ZIG-POEWP-100) connected to the HDBaseT receiver (ZIG-POE-RXAV) – as mentioned previously you also get an amplified audio output for direct connection to speakers, LAN ports for almost anything you choose and for controlling/setting up the devices, relays, a 4K scaler and IR and RS232 control and functionality. 1. Connect sources to POEWP – HDMI and VGA w/Audio 2. Connect RXAV to Display via HDMI 3.
ZIG-RXAV-POE Remote Control Perfect for classrooms when connected to the ZIG-POEWP-100 use the remote to change between HDMI and VGA sources.
WebOS Interface Page Status Control/Defaults Device Name/Notes Firmware/Reset / Info WebOS zigencorp.
Status Local HDBaseT (RXAV in this case) • • • • Link – Green when there is an HDBaseT connection HDMI - Green when HDMI is present Mode: Solid green when HDCP is present, flashing green when no HDCP detected. Cable Length of CAT cable being reported by HDBaseT chip – this is not always 100% accurate, especially with shorter cables.
• • • • • • • • • Serial Number – serial number of RXAV Firmware – Current firmware revision Hardware – for internal use IP Address – IP address of the unit assigned by your DHCP Server Hostname – this is what you want to call the unit – syntax example CR100RX_k123. This is also the name you type into your browser to access the WebOS. Erase Storage – will erase user entered date like installer notes.
Command Structure: ZIG-POE-RXAV RS232 commands <@hostname> <@hostname > indicates the specific target RXAV device, preceded by @ whitespace, space or tab defines the current operation is the variable or the value passed to the device newline char \n, ASCII 0xA [hex] Response Structure: <@hostname> ...
@rxav-01 voldn Decrease device ‘rxav-01’ volume by 1dB Response: @rxav-01 vol x Bass level [range -10dB to +10dB in 2dB steps] @rxav-01 bass 6 Set device ‘rxav-01’ bass level to +6dB Response: @rxav-01 bass x Treble level [range -10dB to +10dB in 2dB steps] @rxav-01 treb -2 Set device ‘rxav-01’ treb level to -2dB Response: @rxav-01 treb x Mute on/off @rxav-01 mute on Set device ‘rxav-01’ mute on Response: @rxav-01 mute x Relay 1 on/off @rxav-01 rel1 on Set device ‘rxav-01’ relay 1 to
Power on/off @rxav-01 pwr off Set device ‘rxav-01’ power off Response: @rxav-01 pwr x Warranty Information 22 ZIG-‐POE-‐RXAV USER MANUAL
LIMITED WARRANTY – with the exceptions noted in the next paragraph, ZIGEN warrants the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of three years from the date of purchase. The proof of sale is required in order to claim warranty. Should this product, in ZIGEN’s opinion, prove defective within this warranty period, ZIGEN, at its option, will repair or replace this product without charge.
