Instruction Manual

ManualsBrandszigbee ManualssortZigbee Namron ZigBee 1 kanal bryter K2 sort

09.ZGK2D.04837

Function introduction

Important: Read All Instructions Prior to Installation

Front side

Back side

Press and hold down both keys together to search and pair to

ZigBee network or factory reset the dimmer switch.

Click to turn on/off the

paired lighting devices

Note: This switch supports 1

group for binding max. 30

lighting devices.

Press and hold down to

decrease/increase light

intensity of the paired

lighting devices

• This device contains a button lithium battery that shall be stored and disposed properly.

• DO NOT expose the device to moisture.

Safety & Warnings

Protocol

Operation Voltage

Transmission Frequency

Transmission Range (free field)

Protection Type

Dimming Range

Dimensions

ZigBee 3.0

3VDC (CR2450)

2.4GHz

30m

IP20

0.1%-100%

71.2x71.2x13.6mm

Product Data

• ZigBee dimmer switch based on ZigBee 3.0

• Enables to pair ZigBee lighting devices via touchlink

commissioning without coordinator

• Supports find and bind mode to pair with ZigBee lighting

devices in the same network

• Supports 1 group for binding max. 30 lighting devices

• 2.4 GHz global operation

• Long battery life mesh technology

• Transmission range up to 30m

• Compatible with universal ZigBee Gateway products

• Compatible with universal single color ZigBee lighting devices

• Compatible with universal ZigBee dimmable lighting devices

ZigBee Clusters Supported by This Remote Are As Follows:

Input clusters:

• Basic • Power Configuration • Identify • Diagnostics

Output clusters:

• Identify • On/off • Level control • Ota

55.57 mm

71.20 mm

11 mm

Battery: CR2450

Before the first use, please open the battery

cover and remove the protective film

55.57 mm

71.20 mm

Quick Start (Simplified operations compared to standard operations in the part “Operation”)

Network pairing mode: click both buttons 3 times (the

remote should not belong to any gateway network).

Factory reset: click both buttons 3 times (the remote

should already be paired to a gateway).

Namron ZigBee 1 kanal bryter K2 sort

Operation

1.This ZigBee dim remote is a wireless transmitter that communicates with a variety of ZigBee compatible systems.

This transmitter sends wireless radio signals that are used to remotely control a compatible system.

2.This ZigBee remote supports 1 group for binding max. 30 lighting devices and enables to control single color ZigBee

lighting devices.

Summary of content (3 pages)

PAGE 1
Namron ZigBee 1 kanal bryter K2 sort 09.ZGK2D.04837 Product Data Protocol ZigBee 3.0 Operation Voltage 3VDC (CR2450) Transmission Frequency 2.4GHz Transmission Range (free field) 30m Protection Type IP20 Dimming Range 0.1%-100% Dimensions 71.2x71.2x13.6mm Important: Read All Instructions Prior to Installation Function introduction Press and hold down both keys together to search and pair to ZigBee network or factory reset the dimmer switch.
PAGE 2
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) 6. Factory Reset Manually LED indicator LED indicator Step 2: From your zigbee controller or hub interface, choose to add device or accessory and enter Pairing mode as instructed by the controller. Step 1: Remove the remote from previous zigbee network if it has already been added to it, otherwise pairing will fail. Please refer to the part "Factory Reset Manually".
PAGE 3
Installation 10. Find and Unbind a Zigbee Lighting Device LED indicator Step 1: Start find and bind mode on the Zigbee lighting device (initiator node) and enable it to find and bind target, refer to its manual. 1.Remove battery insulator ① Use tool to open the silicone gel battery cover ZigBee Lighting Device ②Pull out the battery insulator ③Install the silicone battery cover back Step 3: Short press twice to enable the remote (target node) to find and unbind initiator.