User Manual

0x0002
MAP8,
read-only
Occupancy Sensor Type Bitmap
The type is always 0x01 (PIR)
0x0001
ENUM8,
read-only
Occupancy Sensor Type
The type is always 0x00 (PIR)
0x0010
int16U,
reportable
read-only
PIROccupiedToUnoccupiedDelay
No trigger during this period since last trigger, when time expires, Unoccupied
will be marked.
Value range is 3~28800, unit is S, default value is 30.
Proprietary Attributes:
Attribute Type Description
0x1000
ENUM8,
reportable
PIR Sensor Sensitivity
Default value is 15.
0: disable PIR
8~255: enable PIR, corresponding PIR sensitivity, 8
means the highest sensitivity, 255 means the lowest
sensitivity.
Manufacturer Code
0x1224
0x1001
Int8u,
reportable
Motion detection blind time
PIR sensor is "blind" (insensitive) to motion after last
detection for the amount of time specified in this
attribute, unit is 0.5S, default value is 15.
Available settings: 0-15 (0.5-8 seconds, time
[s] = 0.5 x (value+1))
0x1224
0x1002
ENUM8,
reportable
0: 1 pulse
1: 2 pulses (default value)
2: 3 pulses
3: 4 pulses
Motion detection - pulse counter
This attribute determines the number of
moves required for the PIR sensor to report
motion. The higher the value, the less sensitive
the PIR sensor is.
It is not recommended to modify this parameter
settings!
Available settings: 0~3
0x1224
0x1003
ENUM8,
reportable
PIR sensor trigger time interval
It is not recommended to modify this parameter
settings!
Available settings: 0~3
0: 4 seconds
1: 8 seconds
2: 12 seconds (default value)
3: 16 seconds
0x1224
1.2.6 Alarm-0x0009(Server)
The Alarm Server cluster can generate the following commands:
CmdID Description
0x00
Alarm
Alarm code: Identifying code for the cause of the alarm, as given in
the specification of the cluster whose attribute generated
this alarm.
Please set a valid value of BatteryAlarmMask of Power Configuration.
Power Configuration, alarm code: 0x10.
BatteryVoltageMinThreshold or BatteryPercentageMinThreshold reached for Battery Source
1.3 Application Endpoint #3–IAS Zone
1.3.1 IAS Zone-0x0500(Server)
Attributes Supported:
Attribute Type Description
0x0000
ENUM8,
read-only
Zone State
Not enrolled or enrolled
0x0001
ENUM16,
read-only
Zone Type
is always 0x0D (Motion sensor)
0x0002
MAP16,
read-only
Zone Status
Bit0 support (alarm1)
0x0010
EUI64,
IAS_CIE_Address
0x0011
Int8U,
Zone ID
0x00 – 0xFF
Default 0xff
The IAS Zone Server cluster can generate the following commands:
CmdID Description
0x00
Zone Status Change Notification
Zone Status | Extended Status | Zone ID | Delay
0x01
Zone Enroll Request
Zone Type| Manufacturer Code
The IAS Zone Server cluster can receive the following commands:
CmdID Description
0x00
Zone Enroll Response
Zone Type | Manufacturer Code
1.4 Application Endpoint #3–Temperature Sensor
Cluster Supported Description
0x0000 server
Basic
Provides basic information about the device, such as the manufacturer ID,
vendor and model name, stack profile, ZCL version, production date, hardware
revision etc. Allows a factory reset of attributes, without the device leaving the
network.
0x0003
server
Identify
Allows to put the endpoint into identify mode. Useful for identifying/locating
devices and required for Finding & Binding.
Temperature Measurement
Temperature sensor
0x0402
server