User Manual

ManualsBrandsZida Technologies ManualsElectronicsMotherboard

chapter 4:BIOS Setting

4.5 Integrated Peripherals

On-Chip Primary PCI IDE

Enabled / Disabled on-chip primary PCI IDE. Default setting is "Enabled".

On-Chip Secondary PCI IDE

Enabled / Disabled on-chip Secondary PCI IDE. Default setting is "Enabled".

IDE Primary Master / Slave PIO

IDE Secondary Master / Slave PIO

Specify the IDE mode for the system.

IDE Primary Master / Slave UDMA

IDE Secondary Master / Slave UDMA

Auto / Disabled IDE UDMA function feature. Default setting is "Auto", which lets

BIOS determine.

USB Controller

Enabled / Disabled USB Controller. Default setting is "Enabled".

USB Keyboard Support

Enabled / Disabled USB Keyboard Support in DOS. Default setting is "Disabled"

AC97 Audio

Default setting is "Auto", BIOS will automatically detect onboard AC97 Audio.

AC97 Modem

Default setting is "Auto", BIOS will automatically detect onboard AC97 Modem.

page 38

Mainboard Manual

Summary of content (10 pages)

PAGE 1
chapter 4:BIOS Setting 4.5 Integrated Peripherals On-Chip Primary PCI IDE Enabled / Disabled on-chip primary PCI IDE. Default setting is "Enabled". On-Chip Secondary PCI IDE Enabled / Disabled on-chip Secondary PCI IDE. Default setting is "Enabled". IDE Primary Master / Slave PIO IDE Secondary Master / Slave PIO Specify the IDE mode for the system. IDE Primary Master / Slave UDMA IDE Secondary Master / Slave UDMA Auto / Disabled IDE UDMA function feature.
PAGE 2
Onboard /CNR LAN selection Select "onboard" to enable the optional onboard LAN function.Selects "Ext.CNR " to disable onboard LAN function and uses LAN function on CNR card. Init Display First Default setting is "PCI Slot", sets Init Display First to PCI Slot. Onboard AC97 Control IDE HDD Block Mode Enabled / Disabled IDE HDD Block Mode. Default setting is "Enabled". Power On Function Specifies the keyboard hot key, mouse button, power button to wakeup the computer from S3-S5 state.
PAGE 3
chapter 4:BIOS Setting Use IR pins Setting IR mode.Default is IR_Rx2Tx2. Onboard Parallel Port Specifies the I/O port address of the onboard parallel port. Available settings are Auto, Disable, 378h, 278h and 3BCh. Default is "Auto". Parallel Port Mode Specifies the onboard parallel port mode. Available options are Normal, Bi-Dir, ECP and EPP. Default is "ECP". EPP Mode Select Specifies the Enhanced Parallel Port specification version number.
PAGE 4
chapter 4:BIOS Setting Power Management Setup ACPI Function Enabled/disabled ACPI Function. Default setting is "Disabled". ACPI Suspend Type Specifies ACPI Suspend type. Default setting is "S1(POS)" Power Management Specifies Power Management Mode. Default setting is "User Define". Video Off Method Specifies Video off Method. Default setting is "DPMS". Video Off In Suspend Specifies Video off in Suspend. Suspend Type Specifies Suspend Type. Default setting is "Stop Grant".
PAGE 5
chapter 4:BIOS Setting 4.7 PnP/PCI Configurations Reset configuration Data Enabled \ Disabled Reset configuration Data. Default setting is "Disabled". Resources Controlled by Sets the allocation of PCI resources. Available options are Manual and Auto (ESCD). Default setting is "Auto"(ESCD). BIOS automatically assigns resources. IRQ Resources When resources are controlled manually,assign each system interrupt a type, depending on the type of device using the interrupt.
PAGE 6
chapter 4:BIOS Setting 4.8 PC Health Status Current System Temperature BIOS Setting Current CPU Temperature Detect System and CPU temperature automatically. System Fan Speed CPU Fan Speed Detect Fan Speed Status automatically. Vcore/VDDQ/VCC3-3/+5V/+12V/-12V Detect System Voltage status automatically.
PAGE 7
chapter 4:BIOS Setting 4.9 Frequency Control -9 CPU Clock Ratio Select CPU core/bus frequency ratio. This setting has no effect on processors with frequency ratio locked. Auto Detect PCI CLK Enabled \ Disabled Auto detect PCI CLOCK. Default setting is "Enabled". Spread Spectrum This option turns on/off the Spread Spectrum feature of clock generator to reduce Electromagnetic Interference (EMI) generated by high speed clock signals. Default setting is "Disabled".
PAGE 8
chapter 4:BIOS Setting 4.10 Load Fail-safe Defaults Fail-safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. Load Optimized Defaults BIOS Setting 4.11 Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects.
PAGE 9
chapter 4:BIOS Setting 4.12 Set Supervisor / User password -12 Set Supervisor When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters and press. The new password will clear the previously entered password from CMOS Memory, you will be asked to confirm the Password. Type the password again and press < Enter>.
PAGE 10
chapter 4:BIOS Setting 4.13 Save & Exit Setup Type "Y"will quit the Setup Utility and Save the user setup value to RTC CMOS. Type "N" will return to Setup Utility. Exit Without Saving BIOS Setting 4.14 Type "Y" will quit the Setup Utility and Without Saving the User setup Value. Type "N" will return to Setup Utility.