Standard CMOS Features Time / Date These fields provide you with the current date and time. Note that the hour is displayed as a 24-hour clock. For example, 1:00 PM is 13:00:00. BIOS Setup Floppy Drive A, Floppy Drive B This option selects the type of floppy drives installed.
Advanced CMOS Features Virus Warning Enabled / Disabled Virus Warning function. Default setting is "Disabled". CPU Internal Cache External Cache Enables processor on-chip L1 and L2 cache memory. Available settings are WriteBack, Write-Thru and Disabled. Default is "WriteBack". CPU L2 Cache ECC Cheeking This option enables Error Checking and Correction (ECC) on the processor’s L2 cache bus. Default is "Disabled".
Boot Other Devices Specifies whether BIOS to boot from other device not listed in the 1st/2nd/3rd Boot Device options when BIOS fail to boot from those devices. Default setting is "YES". Swap Floppy Drive Set this option to "Enabled" to permit drives A: and B: to be swapped. Default is "Disabled". Boot Up Floppy Seek Specify whether floppy drive A: will perform a Seek operation at system boot. Default setting is "Disabled".
Advanced Chipset Features SDRAM CAS Latency Time Specifies the number of SCLKs between the time when the Read command is sampled by SDRAM and the Whitney Sample reads data from SDRAM. Available settings are 3(SCLKs) or 2. Default is "3". DRAM Cycle Time Tras/Trc Specifies the length of the SDRAM cycle time in SCLKs. Available options are 7/9, and 5/7. Default is "7/9". SDRAM RAS-to-CAS Delay Specifies the length of the delay inserted between the RAS and CAS signals of the SDRAM system memory access cycle.
CPU Latency Timer Enables CPU BIST. Default is "Disabled". Delayed Transaction Enables / Disables ICH2 (I/O Controller Hub 2) delayed transactions for internal register, Firmware Hub (FWH) and Low Pin Count (LPC) interface accesses. Default is "Disabled". AGP Graphics Aperture Size Sets maximum memory aperture for onboard AGP port. Available settings are 32MB and 64MB. Default is "64MB". System Memory Frequency Sets frequency of DIMM memory. Default is "AUTO".
Power Management Setup ACPI Function Enabled/disabled ACPI Function. Default setting is "Disabled". ACPI Suspend Type Specifies ACPI Suspend type. Default setting is "S1(POS)" Power Management Specifies Power Management Mode. Default setting is "User Define". Video Off Method Specifies Video off Method. Default setting is "DPMS". Video Off In Suspend Specifies Video off in Suspend. Suspend Type Specifies Suspend Type. Default setting is "Stop Grant".
HDD Power Down Specifies HDD Power Down Mode. Default setting is "Disabled". Soft Off by PWR_BTTN Sets Power Down Mode by PWR_BTTN. Default setting is "Instant-off". Wake-Up by PCI card Enabled / Disabled Wake-up by PCI card. Default setting is "Disabled". Power On by Ring Enabled / Disabled Power on by Ring. Default setting is "Enabled". USB KB Wake-up From S3 Enabled / Disabled USB KB Wake-up from S3. Default setting is "Disabled". CPU Thermal-Throttling Monitor CPU Temperature, slow down CPU Speed.
Integrated Peripherals On-Chip Primary PCI IDE Enabled / Disabled on-chip primary PCI IDE. Default setting is "Enabled". On-Chip Secondary PCI IDE Enabled / Disabled on-chip Secondary PCI IDE. Default setting is "Enabled". IDE Primary Master / Slave PIO IDE Secondary Master / Slave PIO IDE Primary Master / Slave UDMA IDE Secondary Master / Slave UDMA Auto / Disabled IDE UDMA function feature. Default setting is "Auto", which lets BIOS determine. USB Controller Enabled / Disabled USB Controller.
AC97 Modem Default setting is "Auto", BIOS will automatically detect onboard AC97 Modem. IDE HDD Block Mode Enabled / Disabled IDE HDD Block Mode. Default setting is "Enabled". Power On Function Specifies the keyboard hot key, mouse button, power button to wakeup the computer from S3-S5 state. Available options are Button only: Password, Hot key, Mouse left, Mouse right, Any key, keyboard 98. Default setting is Button only. KB Power On Password Sets Keyboard Power on Password.
EPP Mode Select Specifies the Enhanced Parallel Port specification version number. This option only appears if the Parallel Port Mode is set to "EPP". The settings are 1.7 or 1.9. Default is N/A because the default setting for the Parallel Port Mode option is not EPP. ECP Mode USE DMA This option only appears if the Parallel Port Mode option is set to ECP. It assigns a DMA channel to the onboard parallel port. Available settings are 1, 3. Default is "3".
