Instruction manual

ManualsBrandsZhone ManualsComputer equipmentSNE2020G-P

SNE2020G-P and SNE2020G-S

2-Port Network Extenders Installation Instructions

Document Number SNE2-A2-GN11-10

July 2005

Contents

Software and Firmware License Agreement ................................................. 2

Product Documentation Online ..................................................................... 3

Introduction ................................................................................................... 4

Package Contents ......................................................................................... 4

Connecting to Power ..................................................................................... 5

Switchpack Configuration ............................................................................. 6

Connecting the SHDSL Lines ....................................................................... 8

Connecting the Ethernet Line ....................................................................... 10

Ferrite Chokes .............................................................................................. 10

LED Indicators .............................................................................................. 11

EMI Notices .................................................................................................. 13

ACTA Customer Information ......................................................................... 13

Supplier's Declaration of Conformity ............................................................. 14

Notice to Users of the Canadian Telephone Network ................................... 15

CE Marking ................................................................................................... 15

Japan Notice ................................................................................................. 15

Important Safety Instructions ........................................................................ 15

Summary of content (16 pages)

PAGE 1
SNE2020G-P and SNE2020G-S 2-Port Network Extenders Installation Instructions Document Number SNE2-A2-GN11-10 July 2005 Contents Software and Firmware License Agreement ................................................. 2 Product Documentation Online ..................................................................... 3 Introduction ................................................................................................... 4 Package Contents ....................................................
PAGE 2
Software and Firmware License Agreement ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
PAGE 3
b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from one state or jurisdiction to another. 6.
PAGE 4
Introduction The family of EFM Based Network Extenders provide an extremely flexible and easy to use solution for providing Ethernet based services to subscribers throughout the service providers network. The SNE2020 is fully DSL The Easy Way™ compliant, so that configuration requirements are removed completely, allowing this device to be installed into the customer premises quickly.
PAGE 5
Connecting to Power Plug the power supply into the Power Adapter port on the back of the SNE2020G and connect it to your power source. Verify that the Power LED on the front of the SNE2020G is illuminated.
PAGE 6
Switchpack Configuration Configuration switches for the SHDSL ports are on the back of the SNE2020G, numbered from left to right, 1–4. Bandwidth: Switches 1–3 (SNE2020G-P Only) Switches 1–3 on the SNE2020G-P provide eight bandwidth options for the two SHDSL ports. Bandwidth for the two ports cannot be configured individually. Distance capabilities listed in the following table assume the use of 26 American Wire Gauge (AWG) cable.
PAGE 7
Ethernet Duplex Mode: Switch 4 The Ethernet link can be configured at either Full Duplex or Half Duplex mode. Although both ends of the ETHERNET connection must have the same duplex mode configuration, it is not necessary for partner providers and subscribers to be configured the same. Duplex mode does not apply to the SHDSL link. Half Duplex Ethernet – Receive and transmit functions are mutually exclusive. Data transmission occurs in only one direction at a time. Packet collisions are not unusual.
PAGE 8
Connecting the SHDSL Lines An SNE2020G-S must be connected via an SHDSL line to an SNE2020G-P, a Mini DSLAM, a Micro DSLAM, or a Broadband Access Concentrator (BAC) interface module. Neither a subscriber-to-subscriber nor a provider-to-provider connection will function. Loop Bonded Connection Using two SHDSL lines for one network connection (loop bonding) will yield twice the speed of a single SHDSL connection. A second SHDSL line also provides a backup should one of the lines become disabled.
PAGE 9
RJ45 Port Cable and RJ45 Connector Table 3.
PAGE 10
Connecting the Ethernet Line Plug the Ethernet cable into the Ethernet Connection RJ45 port on the back of the SNE2020G. Verify the connection: solid illumination of the Ethernet Connection Lnk LED on the front of the SNE2020G indicates a link has been established, if an SHDSL connection has already been made.
PAGE 11
LED Indicators Table 5. LEDs (1 of 2) LED State Indication Additional Information Power Solid Green SNE2020G is operational If the Power LED is not illuminated, it is unlikely the SNE2020G is receiving power. None of the LEDs will be illuminated. SDSL 1 & 2 Pulsing Green* SHDSL connection is established and active Traffic is flowing. Solid Green Problematic SHDSL connection A connection exists but there is indication of a problem with the SHDSL line.
PAGE 12
Table 5. LEDs (2 of 2) LED State Indication Additional Information Ethernet Rx Flashing Amber* Ethernet activity The SNE2020G is receiving data from the Ethernet network. Solid Amber Heavy Rx traffic The SNE2020G is receiving large amounts of data from the Ethernet network. A solid amber Ethernet Rx LED can also signify a lost SHDSL connection. No Illumination No activity Either there is no Ethernet link or a link exists but there is no activity.
PAGE 13
EMI Notices United States – EMI Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 14
If trouble is experienced with this equipment, please contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.
PAGE 15
Notice to Users of the Canadian Telephone Network NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
PAGE 16
3. Do not attempt to service this product yourself, as opening or removing covers may expose you to hazardous voltage or to other risks. Refer all servicing to qualified service personnel. 4. General purpose cables are used with this product for connection to the network. Special cables, which may be required by the regulatory inspection authority for the installation site, are the responsibility of the customer. Use a UL Listed, CSA certified, minimum No.