Instruction manual

ManualsBrandsZhone ManualsComputer equipmentSNE2020G-P

SNE2-A2-ZN13-10 SNE2000G-P and SNE2000G-S 1

SNE2000G-P and SNE2000G-S Network

Extenders

Installation Instructions

Document Number SNE2-A2-ZN13-10

December 2005

Contents

End User License Agreement .................................................................................................... 2

Product Documentation Online ................................................................................................. 3

Introduction ............................................................................................................................... 4

Package Contents ...................................................................................................................... 4

Connecting to Power ................................................................................................................. 5

Configuring the SNE2000G ...................................................................................................... 6

Connecting the SHDSL Line .................................................................................................... 7

Connecting the Ethernet Line .................................................................................................... 8

LED Indicators .......................................................................................................................... 9

EMI Notices .............................................................................................................................. 12

ACTA Customer Information .................................................................................................... 13

Notice to Users of the Canadian Telephone Network ............................................................... 13

Supplier's Declaration of Conformity ....................................................................................... 14

CE Marking ............................................................................................................................... 14

Japan Notice .............................................................................................................................. 14

Important Safety Instructions .................................................................................................... 15

Contacting Global Service and Support .................................................................................... 15

Technical Support ...................................................................................................................... 16

Service Requirements ................................................................................................................ 16

Summary of content (16 pages)

PAGE 1
SNE2000G-P and SNE2000G-S Network Extenders Installation Instructions Document Number SNE2-A2-ZN13-10 December 2005 Contents End User License Agreement .................................................................................................... Product Documentation Online ................................................................................................. Introduction ......................................................................................................................
PAGE 2
End User License Agreement Do not install this Software unless you agree to these provisions. Return the Software promptly for a refund if you do not agree. License. Zhone Technologies, Inc. and/or an affiliate ("Zhone") hereby grants you ("User")—either an individual or a single business entity—the non-exclusive right to install, access, run, or inter.
PAGE 3
MERCHANTABILITY AND NON-INFRINGEMENT. Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from one state or jurisdiction to another. Limit of Liability.
PAGE 4
Introduction Ethernet in the First Mile (EFM) refers to the use of Ethernet starting at the customer premises in subscriber access networks. The family of EFM-based Network Extenders provide an extremely flexible and easy to use solution for providing Ethernet based services to subscribers throughout the service provider’s network. SNE2000G provider and subscriber units can be used in a back to back deployment to provide a point to point configuration.
PAGE 5
Connecting to Power Plug the power supply into the Power Adapter port on the back of the SNE2000G and connect it to your power source. Power Adapter Ethernet Connection Configuration 1 2 3 4 5V DC SDSL Connection 04-17587 Verify that the Power LED on the front of the SNE2000 is illuminated. Upon startup, the Ethernet link will remain disabled (as indicated by no illumination of the Ethernet Rx, Tx, and Lnk LEDs) until the SHDSL connection has been established.
PAGE 6
Configuring the SNE2000G Configuration switches for the SHDSL port are on the back of the SNE2000G, numbered from left to right, 1-4. Bandwidth (SNE2000G-P Only) Switches 1–3 on the SNE2000G-P provide eight bandwidth options for the SHDSL port. Distance capabilities listed in the following tables assume the use of 26 American Wire Gauge (AWG) cable. Connections made with cable of a heavier gauge will link up at greater distances.
PAGE 7
Ethernet Duplex Mode Switch 4 configures Duplex Mode on both the provider and subscriber unit. The Ethernet link can be configured at either Full Duplex or Half Duplex mode. Although both ends of the Ethernet connection must have the same duplex mode configuration, it is not necessary for partner providers and subscribers to be configured the same; duplex mode does not apply to the SHDSL link. z Half Duplex Ethernet – Receive and transmit functions are mutually exclusive.
PAGE 8
Connecting the Ethernet Line Procedure 1 Plug the Ethernet cable into the Ethernet Connection RJ45 port on the back of the SNE2000G. 2 Verify the connection: solid illumination of the Ethernet Connection Lnk LED on the front of the SNE2000G indicates a link has been established, if a DSL connection has already been made.
PAGE 9
LED Indicators The following table describes the behavior of LEDs on the following SNE2000G network extenders: Table 3: LEDs (1 of 2) LED STATE INDICATION ADDITIONAL INFORMATION Power Solid Green SNE2000G is operational If the Power LED is not illuminated, it is likely the SNE2000G is not receiving power, in which case none of the LEDs will be illuminated. Available SHDSL Connection Pulsing Green* SHDSL connection is established and active Traffic is flowing.
PAGE 10
Table 3: LEDs (2 of 2) LED STATE INDICATION ADDITIONAL INFORMATION Ethernet Tx Flashing Amber Ethernet activity The SNE2000G is transmitting data across the Ethernet network. Solid Amber Heavy Tx traffic The SNE2000G is transmitting large amounts of data across the Ethernet network. A solid amber Ethernet Tx LED can also signify a lost SHDSL connection. Solid Green Ethernet connection is established A solid green Ethernet Lnk LED can also signify a lost SHDSL connection.
PAGE 11
RJ45 Pin Assignments SHDSL RJ45 Pin Assignments Table 4: SHDSL RJ45 Pin Assignments Pin Function 1 not used 2 not used 3 not used 4 Ring 5 Tip 6 not used 7 not used 8 not used SNE2-A2-ZN13-10 SNE2000G-P and SNE2000G-S 11
PAGE 12
Ethernet RJ45 Pin Assignments Table 5: Ethernet RJ45 Pin Assignments Pin Function Pin 1 Rx+ Pin 2 Rx– Pin 3 Tx+ Pin 4 not used Pin 5 not used Pin 6 Tx– Pin 7 not used Pin 8 not used EMI Notices United States – EMI Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
PAGE 13
ACTA Customer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of the network extender is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
PAGE 14
Supplier's Declaration of Conformity Place of Issue: Zhone Technologies, Inc.
PAGE 15
! Important Safety Instructions 1 Read and follow all warning notices and instructions marked on the product or included in the manual. 2 Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3 Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord.
PAGE 16
Technical Support If you require assistance with the installation or operation of your product, or if you want to return a product for repair under warranty, contact GSS. The contact information is as follows: E-mail support@zhone.com Telephone (North America) 877-ZHONE20 Telephone (International) 510-777-7133 Internet www.zhone.