Instruction manual

ManualsBrandsZhone ManualsComputer equipmentSNE2000G-S

SNE2000G-P and SNE2000G-S Network Extenders

Installation Instructions

Document Number SNE2-A2-GN13-00

July 2005

Contents

Software and Firmware License Agreement ................................................. 2

Product Documentation Online ..................................................................... 3

Introduction ................................................................................................... 4

Package Contents ......................................................................................... 4

Connecting to Power ..................................................................................... 5

Configuring the SNE2000G .......................................................................... 6

Connecting the SHDSL Line ......................................................................... 7

Connecting the Ethernet Line ....................................................................... 8

LED Indicators .............................................................................................. 9

EMI Notices .................................................................................................. 12

ACTA Customer Information ......................................................................... 12

Supplier's Declaration of Conformity ............................................................. 13

Notice to Users of the Canadian Telephone Network ................................... 14

CE Marking ................................................................................................... 14

Japan Notice ................................................................................................. 14

Important Safety Instructions ........................................................................ 15

Summary of content (16 pages)

PAGE 1
SNE2000G-P and SNE2000G-S Network Extenders Installation Instructions Document Number SNE2-A2-GN13-00 July 2005 Contents Software and Firmware License Agreement ................................................. 2 Product Documentation Online ..................................................................... 3 Introduction ................................................................................................... 4 Package Contents ...........................................................
PAGE 2
Software and Firmware License Agreement ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
PAGE 3
b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from one state or jurisdiction to another. 6.
PAGE 4
Introduction Ethernet in the First Mile (EFM) refers to the use of Ethernet starting at the customer premises in subscriber access networks. The family of EFM-based Network Extenders provide an extremely flexible and easy to use solution for providing Ethernet based services to subscribers throughout the service provider’s network. SNE2000G provider and subscriber units can be used in a back to back deployment to provide a point to point configuration.
PAGE 5
Connecting to Power Plug the power supply into the Power Adapter port on the back of the SNE2000G and connect it to your power source. Power Adapter Configuration 1 2 3 4 Ethernet Connection 5V DC SDSL Connection 04-17587 Verify that the Power LED on the front of the SNE2000 is illuminated.
PAGE 6
Configuring the SNE2000G Configuration switches for the SHDSL port are on the back of the SNE2000G, numbered from left to right, 1-4. Bandwidth (SNE2000G-P Only) Switches 1–3 on the SNE2000G-P provide eight bandwidth options for the SHDSL port. Distance capabilities listed in the following tables assume the use of 26 American Wire Gauge (AWG) cable. Connections made with cable of a heavier gauge will link up at greater distances.
PAGE 7
Ethernet Duplex Mode Switch 4 configures Duplex Mode on both the provider and subscriber unit. The Ethernet link can be configured at either Full Duplex or Half Duplex mode. Although both ends of the Ethernet connection must have the same duplex mode configuration, it is not necessary for partner providers and subscribers to be configured the same; duplex mode does not apply to the SHDSL link. Half Duplex Ethernet – Receive and transmit functions are mutually exclusive.
PAGE 8
Connecting the Ethernet Line Procedure 1. Plug the Ethernet cable into the Ethernet Connection RJ45 port on the back of the SNE2000G. 2. Verify the connection: solid illumination of the Ethernet Connection Lnk LED on the front of the SNE2000G indicates a link has been established, if an SHDSL connection has already been made.
PAGE 9
LED Indicators Table 3. LEDs (1 of 2) ADDITIONAL INFORMATION LED STATE INDICATION Power Solid Green SNE2000G is operational If the Power LED is not illuminated, it is likely the SNE2000G is NOT receiving power, in which case none of the LEDs will be illuminated. Available SHDSL Connection Pulsing Green* SHDSL connection is established and active Traffic is flowing. Solid Green Problematic SHDSL connection A connection exists but there is indication of a problem with the SHDSL line.
PAGE 10
Table 3. LEDs (2 of 2) ADDITIONAL INFORMATION LED STATE INDICATION Ethernet Tx Flashing Amber Ethernet activity The SNE2000G is transmitting data across the Ethernet network. Solid Amber Heavy Tx traffic The SNE2000G is transmitting large amounts of data across the Ethernet network. A solid amber Ethernet Tx LED can also signify a lost SHDSL connection. Solid Green Ethernet connection is established A solid green Ethernet Lnk LED can also signify a lost SHDSL connection.
PAGE 11
RJ45 Pin Assignments SHDSL RJ45 Pin Assignments Table 4. SHDSL RJ45 Pin Assignments Pin Function 1 not used 2 not used 3 not used 4 Ring 5 Tip 6 not used 7 not used 8 not used Ethernet RJ45 Pin Assignments Table 5.
PAGE 12
EMI Notices United States – EMI Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 13
If trouble is experienced with this equipment, please contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.
PAGE 14
Notice to Users of the Canadian Telephone Network NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
PAGE 15
! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord. 4.
PAGE 16
*SNE2-A2-GN13-00* *SNE2-A2-GN13-00* Copyright 2005 Paradyne Corporation. Printed in U.S.A.