Instruction manual

ManualsBrandsZhone ManualsComputer equipmentENE2000-P

SNE2-A2-ZN12-30 1

SNE2040G-P and SNE2040G-S

4-Port Network Extenders

Installation Instructions

Document Number SNE2-A2-ZN12-30

October 2005

Contents

End User License Agreement (Zhone and Affiliates) ............................................................... 2

Product Documentation Online ................................................................................................. 3

Package Contents ...................................................................................................................... 3

Connecting to Power ................................................................................................................. 4

Switchpack Configuration (SNE2040G-P) ............................................................................... 5

Connecting the SHDSL Lines ................................................................................................... 6

SHDSL RJ45 Connector Pinouts .............................................................................................. 7

Connecting the Ethernet Line .................................................................................................... 8

10/100 Ethernet RJ45 Pinouts ................................................................................................... 8

LED Indicators .......................................................................................................................... 9

EMI Notices .............................................................................................................................. 11

ACTA Customer Information .................................................................................................... 11

Supplier's Declaration of Conformity ....................................................................................... 12

Notice to Users of the Canadian Telephone Network ............................................................... 12

CE Marking ............................................................................................................................... 13

Japan Notice .............................................................................................................................. 13

Important Safety Instructions .................................................................................................... 14

Contacting Global Service and Support .................................................................................... 15

Technical Support ...................................................................................................................... 15

Service Requirements ................................................................................................................ 15

Summary of content (16 pages)

PAGE 1
SNE2040G-P and SNE2040G-S 4-Port Network Extenders Installation Instructions Document Number SNE2-A2-ZN12-30 October 2005 Contents End User License Agreement (Zhone and Affiliates) ............................................................... Product Documentation Online ................................................................................................. Package Contents ......................................................................................................................
PAGE 2
End User License Agreement (Zhone and Affiliates) Do not install this Software unless you agree to these provisions. Return the Software promptly for a refund if you do not agree. License. Zhone Technologies, Inc.
PAGE 3
DISCLAIM ALL WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE, MERCHANTABILITY AND NON-INFRINGEMENT. Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from one state or jurisdiction to another. Limit of Liability.
PAGE 4
Connecting to Power Plug the power supply into the Power Adapter port on the back of the SNE2040G and connect it to your power source. Verify that the Power LED on the front of the SNE2040G is illuminated.
PAGE 5
Switchpack Configuration (SNE2040G-P) Configuration switches for the G.SHDSL ports are on the back of the SNE2040G, numbered from left to right, 1–8. Switches 1–3 on the SNE2040G-P together provide eight bandwidth options for the four G.SHDSL ports as a group. Bandwidth cannot be configured individually for the G.SHDSL ports. NOTE: Configuration switches 1–3 are used for G.SHDSL bandwidth configuration on the SNE2040G-P ONLY. The SNE2040G-S determines bandwidth via communication with its partner G.
PAGE 6
Connecting the SHDSL Lines The primary feature of the SNE2040 is loop bonding capability among all four ports. However, both the provider and subscriber units can function with a single G.SHDSL connection. Link up time between local and remote SHDSL network extenders can vary from one to five minutes depending on the quality, gauge and distance of the copper cables.
PAGE 7
SHDSL RJ45 Connector Pinouts RJ45 Port Table 2: Cable and RJ45 Connector SHDSL RJ45 Port Pin Connection 1 not used 2 not used 3 not used 4 Ring 5 Tip 6 not used 7 not used 8 not used SNE2-A2-ZN12-30 7
PAGE 8
Connecting the Ethernet Line If a G.SHDSL connection has not yet been made, the Ethernet link will remain disabled (as indicated by no illumination of the Ethernet 100, Act and Lnk LEDs) until at least one of the four G.SHDSL links has been established. Duplex Mode The 10/100 Ethernet port auto-negotiates speed and duplex mode in accordance with the remote equipment to which it is connected; Ethernet speed and duplex mode configurations cannot be hard set on the SNE2040G.
PAGE 9
LED Indicators This document describes units manufactured after July 2004. See the prior version of this document for information about units manufactured earlier. Upon start up, the Ethernet link is disabled (as indicated by no illumination of the Ethernet 100, Act, and Lnk LEDs) until at least one of the four G.SHDSL connections has been established. Likewise, if established G.
PAGE 10
Table 4: SNE2040G LEDs (Sheet 2 of 2) LED STATE INDICATION ADDITIONAL INFORMATION 100 Mbps Ethernet Link (100) Solid Green 100 Mbps Ethernet connection is established If the Ethernet 100 LED is illuminated, the Ethernet Lnk LED will also be illuminated. No Illumination No 100 Mbps Ethernet connection If the Ethernet 100 LED remains unlit but the Ethernet Lnk LED is illuminated then a connection has been established at 10 Mbps rather than 100 Mbps.
PAGE 11
EMI Notices United States – EMI Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 12
If trouble is experienced with this equipment, please contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Zhone Technologies worldwide office locations, contact Global Service and Support. See Technical Support on page 15.
PAGE 13
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
PAGE 14
! Important Safety Instructions 1 Read and follow all warning notices and instructions marked on the product or included in the manual. 2 Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3 Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord.
PAGE 15
Contacting Global Service and Support Contact Global Service and Support (GSS) if you have any questions about this or other Zhone products. Before contacting GSS, make sure you have the following information: z Zhone product you are using z System configuration z Software version running on the system z Description of the issue Technical Support If you require assistance with the installation or operation of your product, or if you want to return a product for repair under warranty, contact GSS.
PAGE 16
*SNE2-A2-ZN12-30* *SNE2-A2-ZN12-30* 16 SNE2-A2-ZN12-30