User guide

ManualsBrandsZhone ManualsComputer equipmentBSX8000

BSX8-A2-GZ40-00 September 2004 1

BSX8000-5 Broadband Services Switch

Installation Instructions

Document Number BSX8-A2-GZ40-00

September 2004

Contents

Product Documentation Online .......................................................................... 2

Release Notes ................................................................................................... 2

BSX8000-5 Overview ........................................................................................ 2

Unpacking and Inspecting the Equipment ......................................................... 3

Installing a Micro Interface Module (MIM) in the BSX8000-5 ............................ 3

Installing the BSX8000-5 in a BAC .................................................................... 4

Connect the MIM to the Network ....................................................................... 4

BAC Management ............................................................................................. 5

LED Indicators ................................................................................................... 6

Regulatory Compliance for Class A Equipment ................................................. 7

Warranty, Sales, Service, and Training Information ........................................... 7

Summary of content (8 pages)

PAGE 1
BSX8000-5 Broadband Services Switch Installation Instructions Document Number BSX8-A2-GZ40-00 September 2004 Contents Product Documentation Online .......................................................................... 2 Release Notes ................................................................................................... 2 BSX8000-5 Overview ........................................................................................ 2 Unpacking and Inspecting the Equipment ......................
PAGE 2
Product Documentation Online Complete documentation for Paradyne products is available at www.paradyne.com. Select Support → Technical Manuals. To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 1-727-530-2000. Release Notes Release notes for this product are available in the subscriber firmware area of www.paradyne.com. Select Support → Subscriber Firmware. Always review the relevant release notes before installing a new card.
PAGE 3
Unpacking and Inspecting the Equipment HANDLING PRECAUTIONS FOR ! STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, take proper static control precautions to prevent damage to equipment. If you are not sure of the proper static control precautions, contact your nearest sales or service representative.
PAGE 4
Installing the BSX8000-5 in a BAC The 12000E is a 14-slot Broadband Access Concentrator (BAC). Slots 1–12 are reserved for access modules (such as the AIM24000-48) and slots U1 and U2 are reserved for uplink modules. Although not required for operational purposes, if redundancy is desired, two BSX8000-5 modules may be installed in the 12000E, in slots U1 and U2. (Note: For redundancy, the two uplink modules in the chassis must be identical models.) The 4000E is a five-slot BAC.
PAGE 5
MIM-4000F The MIM-4000F is a four-port fiber gigabit Ethernet interface connecting directly to the gigabit Ethernet switch in the BSX8000-5 uplink module. MIM-2E1 or MIM-4E1 Plug your E1 cable into one of the RJ45 E1 ports on the MIM-2E1 or MIM-4E1 faceplate. The MIM-2E1 or MIM-4E1 connects to an E1 network extender provider unit (ENE2000-P, ENE2000-P-12 or, for loop bonding, ENE2020-P) via a standard E1 line.
PAGE 6
LED Indicators Table 1. LED States and Meanings LED State Indication Additional Information PWR (Power) Solid green BSX8000-5 uplink module is receiving power Both BAC power terminals are connected. Pulsing green* BSX8000-5 uplink module is operational Both BAC power terminals are connected. It can take 5-10 seconds after a power-up or reboot, before the LED begins to pulse. Solid amber BSX8000-5 uplink module is receiving power Only one of the two BAC power terminals is connected.
PAGE 7
Regulatory Compliance for Class A Equipment The following regulatory compliance information applies to a BSX8000-5 as installed in a Paradyne BAC. US Federal Communications Commission (FCC) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 8
', .