Specifications

ManualsBrandsZhone ManualsComputer equipmentAIM29000

AIM2-A2-GZ41-00 January 2006 1

AIM29000-48 Interface Module

Installation Instructions

Document Number AIM2-A2-GZ41-00

January 2006

Contents

Software and Firmware License Agreement ...................................................... 2

Product Documentation Online .......................................................................... 3

Release Notes ................................................................................................... 3

Warranty, Sales, Service, and Training Information ........................................... 3

AIM29000 Description ....................................................................................... 4

Unpacking and Inspecting the AIM29000 .......................................................... 4

Installing the AIM29000 in a BLC ...................................................................... 4

Verifying Power .................................................................................................. 6

Connecting the ADSL Cables ............................................................................ 7

ADSL Remote Connection ................................................................................. 11

ADSL RJ21 Pinouts ........................................................................................... 12

Verify the ADSL Connection(s) .......................................................................... 13

LED Indicators ................................................................................................... 13

ADSL Parameters .............................................................................................. 14

AIM29000 Management .................................................................................... 14

Circuit Configuration .......................................................................................... 15

Other Configuration Options .............................................................................. 20

Data Storage ...................................................................................................... 21

Firmware Upgrades ........................................................................................... 22

Regulatory Compliance for Class A Equipment ................................................. 23

Specifications ..................................................................................................... 24

Summary of content (24 pages)

PAGE 1
AIM29000-48 Interface Module Installation Instructions Document Number AIM2-A2-GZ41-00 January 2006 Contents Software and Firmware License Agreement ...................................................... 2 Product Documentation Online .......................................................................... 3 Release Notes ................................................................................................... 3 Warranty, Sales, Service, and Training Information ................................
PAGE 2
Software and Firmware License Agreement ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
PAGE 3
and you may also have other rights which vary from one state or jurisdiction to another. 6.
PAGE 4
AIM29000 Description The AIM29000-48 is a 48-port ADSL2+ Annex A or Annex B inverse multiplexer. It occupies a slot in a Model 4000 or 12000 Broadband Loop Carrier (BLC). Unpacking and Inspecting the AIM29000 HANDLING PRECAUTIONS FOR ! STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation.
PAGE 5
2. With the AIM29000 Printed Circuit Board (PCB) facing right and the AIM29000 model name on the lower edge of the faceplate, align the upper and lower edges of the PCB with the slot module guides. 3. Slide the AIM29000 into the chassis until it is fully seated. Do not use excessive force. 4. Tighten the fastening screws on the AIM29000 faceplate by turning them clockwise with a screwdriver, just until snug. Do not over-tighten the fastening screws. 4-Slot BLC The 4000 and 4000E are five-slot chassis.
PAGE 6
2. With the AIM29000 Printed Circuit Board (PCB) facing up and the AIM29000 faceplate model name on the right, align the edges of the PCB with the slot module guides on both sides. 3. Slide the AIM29000 into the chassis until it is fully seated. Do not use excessive force. 4. Tighten the fastening screws on the AIM29000 faceplate. Do not over-tighten the fastening screws. Verifying Power If you have not already powered up your BLC, do so now.
PAGE 7
Connecting the ADSL Cables 12-Slot BLC NOTE: No configuration is necessary for the AIM29000 to operate at default settings. However, if you wish to run your subscriber connections at settings other than the factory defaults, configure the AIM29000 prior to ADSL connection. Refer to AIM29000 Management on page 14 for further information. Subscriber lines must be connected according to the BLC slot in which the AIM29000 was installed.
PAGE 8
Attaching RJ21 Connectors to the 12-Slot BLC Procedure 1. Detach the hook and loop fastener strap from the RJ21 receptacle. Lift the hook and loop fastener tab on the left and pull the strap open towards the right, leaving it looped under the right side of the connector frame. 2. Slide the RJ21 plug of your ADSL cable underneath the hook and loop fastener from the bottom, and press it firmly into the RJ21 receptacle on the chassis. 3.
PAGE 9
NOTE: If you are using a 120 or 180 degree cable, fasten both the top and the bottom of the RJ21 cable connector to the connector frame on the chassis using the captive screws. 4-Slot BLC Subscriber lines must be connected according to the BLC slot in which the AIM29000 was installed. Interface module slots 1–4 run from bottom to top on the front of the chassis; the corresponding RJ21 ports are directly behind each slot on the back of the chassis (1–4, bottom to top).
PAGE 10
Attaching RJ21 Connectors to the 4-Slot BLC Procedure 1. Detach the hook and loop fastener strap from the female RJ21 connector port: lift the hook and loop fastener tab from the bottom and pull the strap open, towards the top of the chassis, leaving it looped under the top side of the connector frame. 2. Slide the male RJ21 connector of your ADSL cable underneath the hook and loop fastener, from the left, and press it firmly into the female RJ21 connector port on the chassis. 3.
PAGE 11
4. Screw the right side of the RJ21 cable connector into the jackscrew on the right side of the RJ21 connector frame on the chassis. NOTE: If you are using a 120 or 180 degree cable, fasten both the top and the bottom of the RJ21 cable connector to the connector frame on the chassis using the captive screws. ADSL Remote Connection A single line connection can be established between any port on the AIM29000 and any compatible G.lite, ADSL, ADSL2, or ADSL2+ modem.
PAGE 12
ADSL RJ21 Pinouts Table 1.
PAGE 13
Verify the ADSL Connection(s) The LK (Link) LED for each port being connected to a remote modem illuminates solid green to indicate a connection has been established. Link up time between the AIM29000 and remote modems can vary from 15 seconds to five minutes depending on the quality, gauge, and distance of the copper cable pair or pairs being used. LED Indicators Table 2.
PAGE 14
ADSL Parameters No configuration is necessary for the AIM29000 to operate at the default settings. Table 3. AIM29000 Defaults Parameter Default Backbone-VLAN 0 Downstream Speed n/a (Adaptive Port Mode) Flood Uplink Frame Type 1483LLC IP Range 1 0.0.0.0 – 255.255.255.255 IP Range 2-4 0.0.0.0 – 0.0.0.
PAGE 15
Logging In Open an NMS window and log on. You must log on as a Superuser in order to configure the AIM29000. The default Superuser username is: superuser The default Superuser password is: Password Both are case sensitive. Circuit Configuration From the NMS main window, click on any one of the port LEDs depicted on the hardware image to invoke the Circuit Configuration screen. The following parameters may be set on the Circuit Configuration screen.
PAGE 16
Fixed – An AIM29000 port set to port mode fixed will maintain consistant upstream and downstream bandwidths as specified by the user. The link is lost if the speed cannot be maintained. Fixed Adaptive – An AIM29000 port set to port mode fixed adaptive will automatically train up to the best possible speed supported by the AIM29000, the ADSL modem at the remote end, and the copper cable pair connecting the two, within the confines of user-specified maximum upstream and downstream bandwidths.
PAGE 17
DHCP Option 82 Default: Disabled NOTE: DHCP Option 82 is available for configuration in NMS only; it cannot be configured via the CLI or SNMP. Dynamic Host Configuration Protocol (DHCP) Option 82 allows dynamic configuration of IP addresses by adding an identifying string to packets (Option 82) that enables your DHCP Server to recognize which BLC port an IP address request is coming from.
PAGE 18
Virtual Path Identifier (VPI). A VPI is designated by an 8-bit field in ATM cell headers and a VCI is designated by a 16-bit field in ATM cell headers. The AIM29000 supports one PVC per port. On – An AIM29000 port with VPI/VCI Detect on will automatically monitor the line to determine the VPI and VCI settings of the remote ADSL modem to which it is connected, and set itself accordingly. If no ATM cells are detected (at any VPI/VCI setting), the port will default to VPI 0 and VCI 35.
PAGE 19
Unlimited # of MACs Select the check box next to Unlimited # of MACs to limit the number of different MAC addresses permitted to use the port. Define # of MACs Select the check box next to Define # of MACs to limit the MAC addresses permitted to access the port to a specific quantity. Frame Type Default: 1438LLC Frame type is the ADSL data encapsulation method for carrying traffic over an ATM network as defined by the Internet Engineering Task Force (IETF) Request for Comment (RFC) 1483.
PAGE 20
G.lite – G.lite is ADSL technology in compliance with the standards of ITU-T Recommendation G.992.2. The AIM29000 meets the ITU-T Recommendation G992.2 minimum requirements of 512 kbps upstream and 5,136 kbps downstream speeds in G.lite mode. An AIM29000 port that is operating in G.lite mode and utilizing a single line for both phone and data requires an in-line splitter at the local end, and a microfilter at the remote end, of the ADSL connection.
PAGE 21
Data Storage Configuration backup is inherent in the AIM29000. Upon initial power up of the host BLC, default parameters of the AIM29000 will remain in place unless changed through the NMS, CLI, or SNMP. Memory AIM29000 parameter configurations are automatically recorded in both the Random Access Memory (RAM) of the AIM29000 and the Non-Volatile Random Access Memory (NVRAM) of the BLC's management module.
PAGE 22
Downloading a Port Template AIM29000 configuration files can also be flash downloaded from a local file to your BLC's management module via a TFTP tool using a put command. A previously saved port configuration file can be applied to multiple ports on your AIM29000 simultaneously, via your BLC management module, by entering the port value as follows. Table 5. Specifying Multiple Ports for a TFTP Download Method of Entry EXAMPLE: nvr_portcfg.bin.Password.[slot][ports] Comma-separated list nvr_portcfg.bin.
PAGE 23
Regulatory Compliance for Class A Equipment The following regulatory information applies to the AIM29000 as installed in a BLC. NEBS: GR-63-CORE, GR-1089-CORE EMC: FCC Part 15; CSA/C108.8; EN55022, EN55024 SAFETY: UL 60950-1 1st Edition, UL Marking; CSA 22.2 No.
PAGE 24
Specifications Table 6. AIM29000 Specifications Specification Criteria Dimensions 12.75" High x 1.15" Wide x 16.75" Deep (32.4 cm x 2.9 cm x 42.5 cm) Environment Operating Temperature: 32°F to 122°F (0°C to 50°C) in a 12000 BLC –40°F to 149°F (–40°C to 65°C) in a 4000 BLC· Storage Temperature: –40°F to 158°F (–40°C to 70°C)· Humidity: 5% to 95%, non-condensing· Altitude: –200 ft to 16,500 ft (–60 m to 5,000 m) Power –48 VDC (supplied by the host BLC)· 1.6 amps Weight 3.6 lbs (1.