User`s guide

ManualsBrandsZhone ManualsComputer equipment8985

8900-A2-GZ40-40 March 2005 1

ATM Line Cards

Models 8955, 8965, 8968, 8975, and 8985

Installation Instructions

Document Number 8900-A2-GZ40-40

March 2005

Contents

ATM Line Cards ............................................................................................ 1

Software and Firmware License Agreement ................................................. 2

Product Documentation Online ..................................................................... 3

Installation Overview ..................................................................................... 4

Cables You Need .......................................................................................... 4

Installing the Cards in a BLC ........................................................................ 5

Connecting to the ATM or IP Network ........................................................... 6

Connecting 24-Port Models to an MDF or POTS Splitter ............................. 6

Connecting 48-Port Models to an MDF or POTS Splitter ............................. 10

Front Panel LEDs (Models 8955, 8965, 8975, and 8985) ............................. 13

Front Panel LEDs (Model 8968) ................................................................... 14

Logging In to the BLC ................................................................................... 15

Configuration ................................................................................................ 16

Warranty, Sales, Service, and Training Information ...................................... 17

Document Feedback ..................................................................................... 17

Trademarks ................................................................................................... 17

ATM Line Cards

The Models 8955, 8965, 8968, 8975, and 8985 Asynchronous Transfer Mode

(ATM) Line Cards are circuit boards mounted in an 8620 or 8820 Broadband Loop

Carrier (BLC), used to transport ATM cells at high speeds over a single

twisted-pair connection or, optionally, two twisted-pair connections (8985 only).

They must be used in conjunction with a Shelf Concentration and Processing

(SCP) card, which is used to configure and monitor the line cards.

 Model 8955 supports ReachDSL

2.2 concurrent with POTS.

 Models 8965-B2 and 8968 support Asymmetric Digital Subscriber Line

(ADSL), ADSL2, and ADSL2+ concurrent with POTS. The Model 8965 has 24

DSL ports and the Model 8968 has 48 ports.

 Model 8975 supports ReachDSL+, providing ADSL or ReachDSL 2.2 on a

port-by-port basis depending on the capabilities of the line and endpoint.

 Model 8985-B2 supports 2-wire and 4-wire Single-pair High-speed Digital

Subscriber Line (SHDSL).

Summary of content (18 pages)

PAGE 1
ATM Line Cards Models 8955, 8965, 8968, 8975, and 8985 Installation Instructions Document Number 8900-A2-GZ40-40 March 2005 Contents ATM Line Cards ............................................................................................ 1 Software and Firmware License Agreement ................................................. 2 Product Documentation Online ..................................................................... 3 Installation Overview ...............................................
PAGE 2
Software and Firmware License Agreement ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
PAGE 3
6. In no event will Paradyne be liable to Licensee for any consequential, incidental, punitive or special damages, including any lost profits or lost savings, loss of business information or business interruption or other pecuniary loss arising out of the use or inability to use the Software, whether based on contract, tort, warranty or other legal or equitable grounds, even if Paradyne has been advised of the possibility of such damages, or for any claim by any third party. 7.
PAGE 4
Installation Overview Before installing the ATM line card, verify: ❑ That you have obtained the applicable cables; refer to Cables You Need. ❑ That the 8620 or 8820 Broadband Loop Carrier (BLC) is installed and power is supplied to the chassis. Installation of the ATM line card consists of: ❑ Installing the card in the BLC. ❑ Connecting to a Main Distribution Frame (MDF). ❑ Connecting to the uplink. ❑ Configuring your unit using the web interface.
PAGE 5
Installing the Cards in a BLC HANDLING PRECAUTIONS FOR ! STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, take proper static control precautions to prevent damage to equipment. If you are not sure of the proper static control precautions, contact your nearest sales or service representative.
PAGE 6
4. Slide the unit into the slot until the power and network connectors seat firmly in the mating connectors on the backplane. The unit performs a power-on self-test. All of the LEDs turn ON and OFF briefly. When the self-test is completed successfully, the SYSTEM OK LED begins to pulse. If the LED is not pulsing, notify your service representative. 5. Secure the unit by fastening the screws at each end of the faceplate.
PAGE 7
5. Secure the other end of the Telco 50-pin cable by tightening the captive pan-head screw. Cable Tie Anchor Mount Replaced with Supplied #4-40 Phillips Pan-head Screw Telco 50-Pin Connector 01-16900 6. If a ferrite choke is supplied with your line card, clamp it around the cable as close as possible to the chassis. If it fits loosely around the cable, fasten it with a cable tie.
PAGE 8
4. Insert the bottom edge of the locking pivot bracket inside the lower edge of the rear panel cutout next to that connector. Locking Pivot Bracket Rear Panel Cutout Receptacle on Backplane 99-16163d-01 5. Align the two connectors. 6. Rotate the connector until it is fully seated. Rotate 99-16163e-01 7. Tighten the captive screw on the top of the cable's connector. Tighten Screw 99-16163f-01 8.
PAGE 9
Connecting a 24-Port Card to the MDF Procedure To connect the BLC containing the card to an MDF: 1. Connect the cable to the chassis as described in Fastening the Cable with Cable Ties on page 6 or Fastening a Cable with Locking Pivot Brackets on page 7. 2. Dress the cable to the side the connector is nearest. 3. For a Model 8955, 8965, 8975, or 8985 with no POTS service: — Attach the other end of the cable to the appropriate MDF or demarcation point.
PAGE 10
Connecting 48-Port Models to an MDF or POTS Splitter Connect a 48-port ATM line card such as the Model 8968 to an MDF or other demarcation point using the connectors on the faceplate of the card. Connect a cable to the bottom (8820) or right (8620) connector on the card’s faceplate for DSL ports 1–24. Connect a cable to the top (8820) or left (8620) connector on the card’s faceplate for DSL ports 25–48. DC FUSES B -48V A 2 8968 G.DMT G.Lite 8965 G.DMT G.
PAGE 11
Refer to Connector Pin Assignments in the ATM Line Cards, Models 8955, 8965, 8968, 8975, and 8985, User’s Guide for pinouts of the line card connectors. Procedure To connect each receptacle of a 48-port line card to an MDF or POTS splitter: 1. Replace the longer captive screw on your cable connector with the #4-40 Phillips pan-head screw shipped in a plastic bag with the BLC. 2. Install the locking pivot bracket onto the cable end of the connector using the captive screw, as illustrated below.
PAGE 12
Front Cable Management Bracket Installation Instructions (document number 8900-A2-GZ41) for more information.
PAGE 13
Front Panel LEDs (Models 8955, 8965, 8975, and 8985) The following table describes the meaning and states of the LEDs on the front panel of the Model 8955, 8965, 8975, and 8985 line cards. The LEDs of the Models 8955, 8975, and 8985 have similar labeling and meaning. SY SY ST EM EM O O K O K Al Al Off Normal operation, no alarms. Amber, On Test in progress. Off Normal operation, no tests. Amber, Fast Blinking Self-test is in progress. Off Inactive.
PAGE 14
Front Panel LEDs (Model 8968) The following table describes the meaning and states of the LEDs on the front panel of the Model 8968 line card. The card has 24 LEDs to show the state of DSL ports. Depending on the setting of the switch on the face of the card, the LEDs reflect the state of ports 1–24 or 25–48. 25-48 Type LED LED is . . . * Indicating . . . SYSTEM OK Green, On Card failure. System processing functions have stopped. Off No power to card. Green, Pulsing Card functioning normally.
PAGE 15
Logging In to the BLC To access the web interface: Procedure 1. Open your web browser. (Internet Explorer Version 6 or above is recommended.) 2. Type http:// and the IP address of the SCP card into the Address field of your browser window. The default IP address is 10.10.10.10: 3. A login window appears. Enter the User ID and Password, and click on OK. The web interface screen appears. 4. Click on the Configuration menu tab.
PAGE 16
Configuration The following table shows the web interface Configuration screens most likely to require modification, along with some fields found on each screen. Refer to the online Help for more information.
PAGE 17
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com/warranty.
PAGE 18
*8900-A2-GZ40-40* *8900-A2-GZ40-40* 18 March 2005 8900-A2-GZ40-40