Hotwire® ReachDSL™ Modem, Model 6350-A4 with Inline Phone Filter Installation Instructions Document Number 6350-A2-GN12-10 April 2002 Package Checklist Verify that your package contains the following: Rea chD SL PWR ALM TST LINE TX/R X ETH ERN ET Hotwire 6350 ReachDSL Modem Power cord with power transformer DSL interface cable with RJ11 connectors Wiring and Cables You May Need (not supplied) The following standard cables and connectors can be used with this product: Standard RJ11 (or RJ14) wall jac
Installing Additional Phone Filters E SERV P geprufte Sicherheit IC TUY LR 92 99 7 L. AC T.E CE . EQ E1 SS 00 UIPMAR 29 Y 6 EN T R PROD M ad e UCT in TM /N 08 P ho ne Ch in 02 a -3 Be / Fa 39 l Fu br 2se iquè 00 In Ch c. 11 ina 98 Fi lte r E N LI A phone filter is recommended to minimize background noise during a phone conversation on telephones not connected directly to the Hotwire 6350 ReachDSL Modem.
Installing the Hotwire 6350 ReachDSL Modem Place the Hotwire 6350 ReachDSL Modem on a flat surface with clearance for the rear connectors. Procedure 1. UNPLUG TELEPHONE. If a telephone is connected at RJ11 Wall Jack the RJ11 wall jack where the ReachDSL modem will be installed, unplug the telephone line from the wall jack. 2. CONNECT A TELEPHONE. (Optional – go to Step 3 if you are not connecting a telephone to the modem.
. CONNECT TO PC OR ETHERNET HUB. Use an 8-pin Ethernet cable (crossover or straight-through) for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET. Connect to one of the following: — ETHERNET PC. Use an Ethernet crossover cable and connect the other end to a PC with an Ethernet Network Interface Card (NIC) installed. POWER ETHERN ET PC with Ethernet Network Interface Card Ethernet Crossover Cable – or – — Ethernet Hub.
! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord. 4.
Japan – Notices This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules.
Supplier’s Declaration of Conformity Place of Issue: Paradyne Corporation 8545 126th Avenue North Largo, FL 33773-1502 USA Date of Issue: 8/17/2001 Paradyne Corporation, located at the above address, hereby certifies that the Hotwire® ReachDSL™ Model Number 6350-A4-200, bearing labeling identification number US:AW2DL03B6350-A4 complies with: the Federal Communications Commission’s (“FCC”) Rules and Regulations 47 CFR Part 68, the Administrative Council on Terminal Attachments (“ACTA”)-adopted technical
. This equipment cannot be used on public coin service provided by the telephone company. Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information.) 9. An FCC compliant telephone cord with modular plugs may be provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant.
