6218-I2 Wireless Router User’s Guide November 2005 Document Part Number: 6218-A2-ZB23-10
Zhone Technologies @Zhone Way 7001 Oakport Street Oakland, CA 94621 USA 510.777.7000 www.zhone.com info@zhone.com COPYRIGHT 2000–2005 Zhone Technologies, Inc. All rights reserved. This publication is protected by copyright law. No part of this publication may be copied, distributed, displayed, modified, transmitted, stored in a retrieval system, or translated without express written permission from Zhone Technologies, Inc.
! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord. 4.
CE Marking When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Zhone World Wide Web site at www.zhone.com. FCC Part 15 Declaration An FCC Declaration of Conformity may be downloaded from the Zhone World Wide Web site at www.zhone.com. This device complies with Part 15 of the FCC Rules.
plug is provided with this product. It has been designed to be connected to a compatible modular jack that is also compliant. The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0).
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five. If your equipment is in need of repair, contact your local sales representative, service representative, or distributor directly. ! CANADA - EMI NOTICE: This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada.
CONTENTS Document Purpose and Intended Audience ............................................................11 Document Summary ...................................................................................................11 Product-Related Documents ......................................................................................12 Contacting Global Service and Support ..................................................................12 Technical Support ..........................................
ADSL BER Test .........................................................................................................34 Route .............................................................................................................................35 ARP...............................................................................................................................35 Chapter 4 Quick Setup ....................................................................................................
Chapter 7 Management ...........................................................................................................75 Saving and Restoring the Configuration .................................................................75 Backing Up Configuration Settings .........................................................................75 Restoring Configuration Settings .............................................................................77 Restoring Default Settings .......................
6218-I2 Wireless Router User’s Guide 6218-A2-ZB23-10
ABOUT THIS GUIDE Document Purpose and Intended Audience This guide contains detailed information about the 6218-I2 router. It is intended for all users of the router. Document Summary 6218-A2-ZB23-10 Section Description Chapter 1, Introduction Describes the features of the router. Chapter 2, Hardware Installation and PC Setup Shows how to connect the router and set up your PC to manage the router.
Product-Related Documents Complete documentation for Zhone products is available online at www.zhone.com. Contacting Global Service and Support Contact Global Service and Support (GSS) if you have any questions about this or other Zhone products.
INTRODUCTION Introduction Congratulations on becoming the owner of a 6218 wireless router. This User’s Guide will show you how to set up the router, and how to customize its configuration to get the most out of this product. Features The 6218 router has the following features: z z z z 6218-A2-ZB23-10 Built-in Asynchronous Digital Subscriber Line (ADSL) modem which offers G.dmt, G.lite, T1.
Introduction System Requirements In order to use the 6218 wireless router for Internet access, you must have the following: z ADSL service subscription from your ISP z A PC with: — An Ethernet 10/100BaseT network interface card — A processor equivalent to or faster than a Pentium II 133 MHz — 32 MB RAM or greater — Windows 95b, 98, 98SE, 2000, ME, NT, or XP (Note: Windows 95 requires the installation of the Winsock program, not included.
Front Panel Front Panel The front panel contains LED indicators that show the status of the unit. AP xD SL xD LI NK SL LA AC T N1 LA N2 LA N3 LA N4 AL AR M PO W ER 05-17713 Figure 1: Front Panel LEDs Table 1: Front Panel Label and LEDs Label Color xDSL LNK Green Function On: ADSL link is established. Flashing: ADSL link is established and active. Off: No ADSL link. xDSL ACT Green Off: No PPP connection is established or the connection is not used.
Introduction Rear Panel ON/OFF POWER LAN4 LAN3 LAN2 RESET LAN1 LINE CONSOLE DEFAULT 05-17714 Figure 2: Back Panel The rear panel contains the ports for the router's data and power connections.
HARDWARE INSTALLATION AND PC SETUP Overview This chapter provides basic instructions for connecting the router to a computer or a LAN and to the Internet using DSL. The first part provides instructions to set up the hardware, and the second part describes how to prepare your PC for use with the router. It is assumed that you have already subscribed to DSL service with your Internet service provider (ISP).
Hardware Installation and PC Setup Connecting the Hardware Shut down your PC and any other equipment before connecting it to the router. To connect your router: 1 Verify that the router’s power switch is in the Off (outward) position. Verify that any PCs and other LAN devices you will attach (such as hubs or switches) are turned off. 2 Use the provided modular phone cable to connect the LINE jack of the router to your RJ11 wall jack.
Connecting the Hardware ON/OFF POWER LAN4 RESET DEFAULT LAN3 LAN2 LAN1 LINE CONSOLE 05-17715 Figure 3: Hardware Installation Table 3: LED Indicators This LED . . . Should be: POWER Solid green to indicate that the device is turned on. If this light is not on, check if the power adapter is attached to the router and plugged into an AC power source.
Hardware Installation and PC Setup Configuring Your Computer Before you can access the router over the LAN you have to configure your PC's TCP/IP address to be 192.168.1.x (where x is any number between 3 and 254), with a subnet mask of 255.255.255.0. Your router's default IP address is 192.168.1.1. If you know the version of Windows that you use, go to the appropriate section below to learn how to set the IP address of your PC.
Configuring Your Computer Windows XP 1 In the Windows task bar, click on the Start button, and then click on Control Panel. 2 Double-click on the Network Connections icon. 3 In the LAN or High-Speed Internet window, right-click on the icon corresponding to your network interface card (NIC), and select Properties. (Often this icon is labeled Local Area Connection). The Local Area Connection dialog box displays with a list of currently installed network items.
Hardware Installation and PC Setup Figure 7: Local Area Connection Properties (Windows XP) 5 In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio button labeled Use the following IP address. Type an address between 192.168.1.3 and 192.168.1.254 in the IP Address field (192.168.1.20 is shown here as an example) and 255.255.255.0 in the Subnet Mask field. Figure 8: TCP/IP Properties (Windows XP) 6. Click on OK twice to confirm your changes, and close the Control Panel.
Configuring Your Computer Windows 2000 1 In the Windows task bar, click on the Start button, point to Settings, and then click on Control Panel. 2 Double-click on the Network and Dial-up Connections icon. 3 In the Network and Dial-up Connections window, right-click on the Local Area Connection icon, and then select Properties. The Local Area Connection Properties dialog box display a list of currently installed network components.
Hardware Installation and PC Setup The Network Properties dialog box displays a list of currently installed network components. If the list includes Internet Protocol (TCP/IP), the protocol has already been enabled; skip to Step 11. 4 If Internet Protocol (TCP/IP) does not appear as an installed component, click on Add. 5 In the Select Network Component Type dialog box, select Protocol, and then click on Add. 6 Select Microsoft in the Manufacturers box.
Configuring Your Computer You may be prompted to install files from your Windows 95/98 installation CD. Follow the instructions to install the files. 7 Click on OK to restart the PC and complete the TCP/IP installation. 8 After restarting your PC, open the Control Panel window, and then click on the Network icon. 9 Select the network component labeled TCP/IP, and then click on Properties. If you have multiple TCP/IP listings, select the listing associated with your network card or adapter.
Hardware Installation and PC Setup 192.168.1.3 and 192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask field. 11 Click on OK twice to confirm and save your changes, and then close the Control Panel. Logging in to Your Router This section shows how to connect to the router's web interface, configure settings, and observe some statistics of your Internet connection. 1 Open your Web browser, and type the following URL in the address/ location box, and press Enter: http://192.168.1.
Logging in to Your Router 2 Enter your user name and password, and then click on OK to display the home page of the router's web interface. There are two default user name and password combinations: Table 4: Default User Names and Passwords User Name Password Capability user user Can display device status, but cannot change or save configuration options. admin admin Can perform all functions. You can change the passwords at any time. The home page is shown in Figure 10.
Hardware Installation and PC Setup 28 6218-I2 Wireless Router User’s Guide 6218-A2-ZB23-10
DEVICE INFORMATION Status Summary Display the general status report for the router by clicking on Summary under Device Info (Figure 11).
Device Information WAN Display the WAN status report from the by clicking on WAN under Device Info (Figure 12). Figure 12: WAN Status When a WAN connection is configured, the screen looks like Figure 13.
LAN Statistics LAN Statistics Display LAN statistics by clicking on LAN under Statistics (Figure 14). Figure 14: LAN Statistics WAN Statistics Display WAN statistics by clicking on WAN under Statistics (Figure 15).
Device Information ATM Statistics Display ATM statistics by clicking on ATM under Statistics (Figure 16).
ADSL Statistics ADSL Statistics Display ADSL statistics by clicking on ADSL under Statistics (Figure 17).
Device Information ADSL BER Test The ADSL Bit Error Rate (BER) test determines the quality of the ADSL connection. The test is performed by transferring idle cells containing a known pattern and comparing the received data with this known pattern to check for any errors (Figure 18 and Figure 19). To run a BER test: 1 Click on the ADSL BER Test button. 2 Select the test duration and click on Start 3 Check the result.
Route Route Obtain the Routing status report by clicking on the Route item under Device Info (Figure 20) Figure 20: Route Information ARP Display the ARP status report by clicking on ARP under Device Info (Figure 21) Figure 21: ARP Status 6218-A2-ZB23-10 6218-I2 Wireless Router User’s Guide 35
Device Information 36 6218-I2 Wireless Router User’s Guide 6218-A2-ZB23-10
QUICK SETUP Quick Setup with Auto-Connect Enabled Auto-connect will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To use auto-connect: 1 Select Quick Setup. The Quick Setup initial screen appears.
Quick Setup 2 Select DSL Auto-Connect, then click on Next. The progress information screen appears.
Quick Setup with Auto-Connect Disabled Quick Setup with Auto-Connect Disabled 1 Select Quick Setup. The Quick Setup initial screen appears. 2 Verify that DSL Auto-Connect is not selected. Entry boxes for VPI and VCI appear when DSL Auto-Connect is not selected. 3 Specify VPI and VCI as directed by your ISP. Figure 25: Specifying VPI and VCI 4 Click on Next. The Connection Type screen appears. Figure 26: Connection Type 5 Select the protocol and encapsulation type required by your ISP.
Quick Setup 6 Click on Next. Further parameters for the selected protocol are presented. For example, if you selected PPPoA, the PPP Username and Password screen appears. Figure 27: PPP Username and Password 7 Click on Next. The Network Address Translation Settings screen appears.
Quick Setup with Auto-Connect Disabled 8 Enter the settings specified by your ISP and click on Next. The Device Setup screen appears. Figure 29: Device Setup 9 If desired, configure configure the DSL Router IP address and Subnet Mask for the LAN interface to correspond to your LAN's IP Subnet. If you want the DHCP server to automatically assign IP addresses, then enable the DHCP server and enter the range of IP addresses that the DHCP server can assign to your computers.
Quick Setup 10 Click on Next to continue. The WAN Setup Summary screen displays all WAN settings that you have made. Check that the settings are correct before clicking on the Save / Reboot button. Clicking on Save / Reboot saves your settings and restarts your router.
ADVANCED SETUP WAN Set up WAN parameters as directed by your ISP.
Advanced Setup Add Function – ATM PVC Configuration If you want to add a new rule for the WAN interface, click on the Add button. The ATM PVC Configuration screen appears. The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category. Figure 32: ATM PVC Configuration Screen Verify the following values with your ISP before you change them. z VPI (Virtual Path Identifier) – The valid range is 0 to 255.
WAN Connection Type Screen 1 Select the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use, then click on Next button. Figure 33: Connection Type Screen 2 Select a connection type and click on Next. In this example, the Bridge Service screen appears. Figure 34: Bridge Service Screen 3 Enter or select the parameters presented for the service type, and click on Next. The WAN Setup - Summary screen appears.
Advanced Setup WAN Setup - Summary 1 Make sure that the settings on the WAN Setup - Summary screen match the settings provided by your ISP. If all settings are correct, click on the Save button to save these settings; if not, click on the Back button to make any modifications. If you want to change any item after saving, click on the Edit button to make any modifications.
WAN WAN Setup Finish After you change any item in WAN Setup, click on the Finish button to apply the changes and reboot the system.
Advanced Setup Local Area Network (LAN) Setup You can configure the DSL Router IP address and Subnet Mask for the LAN interface to conform your LAN's IP Subnet. The Save button only saves the LAN configuration data. The Save/Reboot button saves the LAN configuration data and reboots the router to make the new configuration effective.
NAT NAT You can configure the Virtual Server, Port Triggering, and DMZ Host when NAT is enabled. Virtual Servers A virtual server allows you to direct incoming traffic from the WAN side to a specific IP address on the LAN side. Click on the Add button to add a virtual server.
Advanced Setup You can select a Service or make new one. Enter the Server IP Address, then click on Save/Apply to submit your configuration. Figure 40: Virtual Server Add Screen On this screen you can view and delete servers. Click in the check box under Remove and click on the Remove button to delete selected virtual servers.
Port Triggering Port Triggering Click the on the Add button to add Port Triggering for your Internet application. Figure 42: Port Triggering Setup Page You can select an application every time or create new one for your application. Then click on Save/Apply to save your settings.
Advanced Setup The Port Triggering list screen appears after you save your selections. You can delete an entry by clicking in the Remove column then clicking on the Remove button. Figure 44: Port Triggering List DMZ Host You can define the IP address of the DMZ Host on this screen. Enter the IP address and click on Save/Apply.
Firewall Firewall For security reasons, firewall options can be configured only from the LAN side of the router. IP Filtering – Outgoing The outgoing filter will block the traffic from the LAN side to the WAN side. Click on Add to create filters. Figure 46: IP Filtering – Outgoing Filter Setup Input the filter name, source information (from the LAN side), and Destination information (from the WAN side). Then click on Save/Apply.
Advanced Setup IP Filtering – Incoming Incoming filter filters the traffic from the WAN side to the LAN side. Click on Add to add incoming filter settings. Figure 48: IP Filtering – Incoming Filter Setup Page Enter a filter name, information about the source address (from the WAN side), and information about the destination address ( to the LAN side). Select the protocol and WAN interface. Then click on Save/Apply to add the setting.
Firewall Firewall – MAC Filtering MAC filtering can forward or block traffic by MAC address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen. Figure 50: IP Filtering - MAC Filtering Setup If you click on Change Policy, a confirmation dialog lets you verify your change.
Advanced Setup If you want to add a setting to the MAC filtering table, enter the Source and Destination MAC address, and select protocol type, frame direction, and WAN interface. Then click on Save/Apply to save it.
Port Mapping Port Mapping Use the Port Mapping screen to map multiple ports to a PVC and create bridging groups. Each group will perform as an independent network. Figure 53: Port Mapping To create a new mapping group: 1 Click on Add. The Port Mapping Configuration screen appears. Figure 54: Creating a Port Mapping Entry 2 Enter a unique Group name.
Advanced Setup 4 Click on Save/Apply. Quality of Service You can configure the Quality of Service to apply different priorities to traffic on the router. Figure 55: Quality of Service Setup Click on Add and the Add Network Traffic Class Rule screen appears. To add a rule: 1 Give a name to this traffic class. 2 Assign a priority level-low, medium, and high-to this traffic class. 3 Select an IP precedence from the range of 0–7.
Routing – Default Gateway Figure 56: Quality of Service Add Screen Routing – Default Gateway You can change the Default Gateway on the Routing - Default Gateway screen. By default the Enable Automatic Assigned Default Gateway box is checked.
Advanced Setup If you want to specify the default gateway address, then uncheck the box as seen below. Enter the default gateway address and, optionally, the WAN interface you will use. Click on Save / Apply to save the settings. If you add or change the default gateway address, you must reboot the router to put the new default gateway IP address into effect. Figure 58: Default Gateway Setup Routing – Static Route Use the Routing - Static Route screen to add a static route to the routing table.
Routing – RIP Enter the route information and click on Save/Apply to make it active. No reboot is required. Figure 60: Static Route Add Routing – RIP If RIP is enabled, the router operation can be configured as Active or Passive.
Advanced Setup DNS Server Use the DNS Server screen to request automatic assignment of a DNS or to specify a primary and secondary DNS. Figure 62: DNS Setup Dynamic DNS Use the Dynamic DNS screen to alias a dynamic IP address to a static hostname, allowing your router to be easily accessed from anywhere on the Internet.
Dynamic DNS To set up a Dynamic DNS entry: 1 Click on Add. The Add Dynamic DNS screen appears. Figure 64: Adding a Dynamic DNS Entry 2 Select a D-DNS Provider from the drop-down list. 3 Enter the Hostname you have selected for the interface. 4 Select the router Interface from the drop-down list. 5 Enter the information you used to register with the dynamic DNS service: for DynDNS, enter your Username and Password; for TOZ, enter your E-mail address and Key. 6 Click on Save/Apply.
Advanced Setup ADSL There are three major items in the ADSL settings. Figure 65: DSL Settings Modulation Methods The following modulation methods are supported by the 6218 wireless router: z z z z z z G.dmt Enabled G.lite Enabled T1.413 Enabled ADSL Enabled Annex L Enabled ADSL2+ Enabled. Do not change this setting unless so directed by your ISP. Phone Line Pair The 6218 wireless router supports phone lines on pins 2 and 3 or pins 1 and 4 to connect your ADSL line.
DSL Advanced Settings Capability The following are included under Capability: z Bitswap Enable z SRA (Seamless Rate Adaptation) Enable Do not change these settings unless so directed by your ISP. DSL Advanced Settings Do not change the DSL Advanced Settings unless so directed by your ISP. To view the DSL Advanced Settings screen, click on the Advanced Settings button on the DSL Settings screen (see Figure 65).
Advanced Setup z z No Retrain: In this mode the router will try to establish a connection as in normal mode, but once the connection is up it will not retrain if the signal is lost. L3: Puts the router into the L3 power state. Select a test mode and click on Apply. Then click on Tone Selection. Tone Selection To view the ADSL Tone Settings screen, click on the Tone Selection button of the DSL Advanced Settings screen (see Figure 66).
Wireless Wireless The Wireless screens let you configure the settings for wireless access, security, and protocols. Wireless - Basic The Wireless - Basic screen lets you enable or disable Wi-Fi capability in the router. The default setting for wireless is enabled. From this screen you can also hide the access point so others cannot see your ID on the network.
Advanced Setup about the RADIUS server such as its IP address, port and key must be entered. WEP encryption is also enabled and the encryption strength must also be selected. z z z z z z WPA (Wi-Fi Protected Access) – Usually used for the larger enterprise environment, it uses a RADIUS server and TKIP (Temporal Key Integrity Protocol) encryption (instead of WEP encryption, which is disabled). TKIP uses 128-bit dynamic session keys (per user, per session, and per packet keys).
Wireless Wireless - MAC Filter The MAC filter screen allows you to manage MAC address filters. Add the MAC addresses that you want to manage and then select the mode that you want to use to manage them. You can disable this feature or you can allow or deny access to the MAC addresses that you add to the list. Figure 70: Wireless – MAC Filter The following screen appears when you want to add a MAC address to the filter.
Advanced Setup Wireless - Bridge The Wireless - Bridge screen lets you determine whether the router acts as an access point or a wireless bridge. Figure 72: Wireless – Bridge Wireless - Advanced The Wireless - Advanced screen lets you configure advanced features of the wireless LAN network: z z z z z z z z 70 AP Isolation – If you select enable, then each of your wireless clients will not be able to communicate with each other. Band – The default setting is 2.4GHz - 802.11g Channel – 802.
Wireless z z z z z Beacon Interval – A packet of information that is sent from a connected device to all other devices where it announces its availability and readiness. A beacon interval is a period of time (sent with the beacon) before sending the beacon again. The beacon interval may be adjusted in milliseconds (ms). Xpress Technology – A technology that utilizes standards based on framebursting to achieve higher throughput.
Advanced Setup 72 6218-I2 Wireless Router User’s Guide 6218-A2-ZB23-10
DIAGNOSTICS Testing the DSL Connection The diagnostics screen allows you to run diagnostic tests to check your DSL connection. The screen shows test results for three connections: z Connection to your local network z Connection to your DSL service provider z Connection to your Internet service provider Use the Test and Test with OAM F4 buttons to retest if necessary.
Diagnostics 74 6218-I2 Wireless Router User’s Guide 6218-A2-ZB23-10
MANAGEMENT Saving and Restoring the Configuration The configuration of your router can be backed up to a file, and also can be restored from a file. You can also restore the router to its factory default configuration. Backing Up Configuration Settings To back up your settings, select Management -> Settings -> Backup Settings.
Management Verify that you would like to save the file. Figure 76: Backup Settings Upload Confirmation Select the location where you want to save the file.
Restoring Configuration Settings Restoring Configuration Settings To restore saved settings, select Management -> Settings -> Restore User Settings. Figure 78: Restore User Settings Screen Select the backup file you want to restore and click on Update Settings.
Management The router will restore settings and reboot to activate the restored settings.
Restoring Default Settings Restoring Default Settings Restore Default will erase all current settings and restore the router to factory default settings. To restore the router to factory default settings, select Management -> Settings -> Restore Default. Figure 81: Restore Default Settings Screen Reply OK to the confirmation dialog.
Management The router will restore the default settings and reboot. Figure 83: Restore Default Settings Reboot System Log The System Log dialog allows you to view the System Log and configure the System Log options.
System Log View System Log Click on the "View System Log" button to check the log file.
Management Configure System Log If the log is enabled, the system will log selected events: Emergency, Alert, Critical, Error, Warning, Notice, Informational, and Debugging. All events above or equal to the selected log levels will be logged (maintained in the system log file) and displayed. If the selected mode is Remote or Both, events will be sent to the specified IP address and UDP port of a remote system log server. If the selected mode is Local or Both, events will be recorded in the local memory.
SNMP SNMP Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in the router. Use the SNMP screen to set up parameters for SNMP access. Figure 87: SNMP Screen Select the desired values and click on Save/Apply to configure the SNMP options.
Management Internet Time Use the Internet Time screen to specify whether the router uses Simple Network Time Protocol (SNTP) to obtain the time of day from NTP servers on the Internet. To set up the router to obtain time from an NTP server: 1 Select “Automatically synchronize with Internet time servers”. The SNTP fields appear. Figure 88: Internet Time Screen 2 Select NTP servers. 3 Specify the time zone offset for your router’s location. 4 Click on Save/Apply.
Access Control – Services Access Control – Services You can enable or disable some services of your router by LAN or WAN. If no WAN connection is defined, only the LAN side can be configured. Figure 89: Services Setup Access Control – IP Addresses Web access to the router can be limited when Access Control Mode is enabled. The IP addresses of allowed hosts can be added using Access Control -> IP Address.
Management To assign the IP address of the management station that is permitted to access the local management services, enter the IP address in the box and click on the Save/Apply button. Figure 91: Access Control – IP Address Add Screen Access Control – Passwords Use Access Control -> Passwords to change a password. Select an account and enter the current password and the new password. Then click on Save/ Apply.
Update Software Update Software If your ISP releases new software for this router, follow these steps to perform an upgrade. 1. Obtain an updated software image file from your ISP. 2. Enter the path to the image file location or click on the "Browse" button to locate the image file. 3. Click on the Update Software button once to upload the new image file. Figure 93: Update Software Note The update process takes about two minutes to complete, and your router will reboot automatically.
Management Reboot Router Select Management -> Reboot Router to reboot the router using the web interface. The router will save the current configuration and reboot itself using the new configuration. The rebooting process takes about two minutes to complete.
SPECIFICATIONS Specifications are subject to change without notice. Table 5: 6218-I2 Specifications 6218-A2-ZB23-10 Specification Criteria DSL Protocol Support ANSI T1.413 (Full Rate ADSL) ITU G.992.1 (DMT) ITU G.992.2 (G.lite) ITU G.992.3 (ADSL2) ITU G.992.5 (ADSL2+) ITU G.994.1 (G.hs) ITU G.997.
Specifications 90 6218-I2 Wireless Router User’s Guide 6218-A2-ZB23-10
INDEX A About This Guide 11 Access Control IP Addresses 85 Passwords 86 Services 85 ADSL 64 BER Test 34 Statistics 33 Advanced Settings, DSL 65 Advanced Setup 43 ARP 35 ATM PVC Configuration 44 Statistics 32 DNS 62 Dynamic 62 Document Purpose and Intended Audience 11 Summary 11 Domain Name Server 62 Dynamic DNS 62 E EMI Notice Canada 6 Japan 6 Environment 89 Ethernet cable 18 B F Backing Up Configuration Settings 75 BER Test 34 Bridge Service 46 Bridging groups 57 FCC Part 15 Declaration 4 Features 13
Access Control 85 Of Router 20 IP Filtering Incoming 54 Outgoing 53 J Japan Notices 6 L Local Area Network (LAN) ports, connecting 18 Setup 48 Statistics 31 Logging In 29 M MAC Filtering 55 Management 75 Mapping ports 57 Modulation Methods 64 N NAT 49 Network Interface Card 18 Notice to Users of the Canadian Telephone Network 5 to Users of the United States Telephone Network 4 O Operating Environment 89 P Parts List 14 Password Access Control 86 Default 27 PC Setup 17 Phone Line Pair 64 Port Mapping 5
System Requirements 14 Virtual Servers 49 T W Test BER 34 DSL Connection 73 Time 84 Tone Selection 66 WAN 30, 43 Setup 46 Statistics 31 Status 30 Web Interface Home Page 27 Using 29 Weight 89 Windows 2000 23 Windows 95 24 Windows 98 24 Windows ME 23 Windows NT 25 Windows XP 21 U Update Software 87 User Name, Default 27 V View System Log 81 6218-A2-ZB23-10 6218-I2 Wireless Router User’s Guide 93
6218-I2 Wireless Router User’s Guide 6218-A2-ZB23-10
