Specifications

ManualsBrandsZhone ManualsComputer equipment5620

Hotwire

5620 RTU

Installation Instructions

Document Number 5620-A2-GN11-40

September 2001

Contents

Hotwire 5620 RTU Overview ........................................................................ 1

Product Documentation Online ..................................................................... 4

Getting Started .............................................................................................. 5

Installing the DSL Access Wiring .................................................................. 6

Connecting to the DSL Access Wiring .......................................................... 8

Installing the Hotwire 5620 RTU ................................................................... 9

Power-On ...................................................................................................... 13

Troubleshooting ............................................................................................. 14

Increasing the Number of End-User Systems .............................................. 15

Cables & Connectors .................................................................................... 15

Optional RTU Wall Placement ...................................................................... 17

Technical Specifications for the Hotwire 5620 RTU ...................................... 19

Important Safety Instructions ........................................................................ 20

Government Requirements ........................................................................... 22

Warranty, Sales, Service, and Training Information ...................................... 24

Hotwire 5620 RTU Overview

The Hotwire

5620 RTU (Remote Termination Unit) is a component in the Hotwire

RADSL Access System and interoperates with the Hotwire 8373, 8374, or 8510 DSL

Card in the DSLAM (Digital Subscriber Line Access Multiplexer) system. This system

provides high-speed Internet or corporate LAN access over traditional twisted-pair

copper telephone wiring.

Copper pairs run from the central office (CO) to the customer premises (CP) to create

the local loop. The local loop terminates on the customer premises at the demarcation

point in a punchdown block or network interface device (NID).

Summary of content (24 pages)

PAGE 1
Hotwire® 5620 RTU Installation Instructions Document Number 5620-A2-GN11-40 September 2001 Contents Hotwire 5620 RTU Overview ........................................................................ 1 Product Documentation Online ..................................................................... 4 Getting Started .............................................................................................. 5 Installing the DSL Access Wiring .........................................................
PAGE 2
NOTE: In this document: — End-user system is used to represent any host with an Ethernet connection. — Service provider is used to represent any Internet Service Provider (ISP) or remote LAN access provider. DSL Access with a Hotwire 5030 POTS Splitter An optional POTS (plain old telephone service) splitter can be installed to block out the DSL signal and allow the POTS frequencies to pass through.
PAGE 3
DSL Access without a POTS Splitter When the Hotwire 5620 RTU is installed without a POTS splitter, the DSL line is used for data only and does not provide telephone services.
PAGE 4
There are two Hotwire phone filters that can be used with the 5620 RTU: Hotwire 6035 Universal Phone Filter is designed for use with a tabletop phone. Hotwire 6040 Universal Wall Jack Phone Filter is designed for use with a wall phone.
PAGE 5
Getting Started Before beginning your RTU’s installation, make sure that you have all the equipment you will need. Package Checklist In addition to these instructions, verify that your package contains the following: ❑ Model 5620 Remote Termination Unit (RTU) ❑ DSL interface cable with RJ11 modular plugs ❑ Power cord with power transformer Wiring and Connectors You Will Need The following wiring and standard connectors are used with this product: ❑ Standard RJ11 wall jack for the DSL cabling.
PAGE 6
Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to an RJ11 jack. Typically, the punchdown block is installed in commercial locations and the NID is installed in residential locations. Procedure 1. Access the punchdown block or NID. 2. Disconnect the DSL access pair from the local loop.
PAGE 7
3. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack. In the following example, a NID is used without a POTS splitter. It includes an existing POTS line and a second pair installed for DSL access.
PAGE 8
Connecting to the DSL Access Wiring The Hotwire 5620 RTU connects to the local loop via wiring from the demarcation point to an RJ11 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ11 jack or replace a single jack with a double RJ11 jack. Customer Premises Demarcation Point DSL Twisted-pair Wiring DSL RJ11 Jack Central Office POTS/DSL Local Loop RTU Punchdown Block or NID 97-15343-02 Procedure 1.
PAGE 9
Installing the Hotwire 5620 RTU Place the Hotwire 5620 RTU on a flat surface with clearance for the rear connectors. Connecting the DSL Line in a Home Environment (Phone and RTU in the Same Location) Use the supplied RJ11 6-pin cable for the DSL connection. You will also need a multiple line adapter and a phone filter (see Phone Filters on page 3). Procedure 1. Insert a multiple line adapter into the wall jack. 2. Insert one end of the cable into the DSL jack on the RTU. 3.
PAGE 10
Connecting the DSL Line in All Other Environments Use the supplied RJ11 6-pin cable for the DSL connection. Procedure 1. Insert one end of the cable into the DSL jack on the RTU. 2. Insert the other end into the wall jack.
PAGE 11
Connecting the Ethernet Cable Use an 8-pin Ethernet straight-through or crossover cable for the Ethernet connection. Procedure To connect an Ethernet Hub using a straight-through cable: — Insert one end of the straight-through cable into the ETHERNET jack on the router and connect the other end to an Ethernet hub. Do not connect it to the hub’s optional Uplink connection; the Uplink connection requires an Ethernet crossover cable.
PAGE 12
Connecting Power Procedure 1. Insert the supplied power cord’s round end into the POWER jack on the RTU. 2. Plug the transformer into an AC outlet. Hotwire RTU Power Jack P OW E R or ETHER NET DSL Transformer or 01-15836-01 The RTU hardware installation is now complete. When the power cord is installed, the RTU goes through a power-on self-test.
PAGE 13
Power-On When power is applied, the RTU performs self-diagnostics and the PWR LED is on. The self-diagnostics includes a power-on self-test. During the power-on self-test, all of the LEDs turn on for one second. Power – green Alarm – red Test – yellow Digital Subscriber Line – green Ethernet Link – green PWR ALM TST DSL ETHERNET 5620 TM 98-15835 Status LEDs All of the LEDs turn on and off during the power-on self-test.
PAGE 14
Troubleshooting LED Symptom Action All LEDs are on. If the LEDs remain on for more than ten minutes, the RTU is not functional. Unplug the unit and reapply power. If the ALM LED is still on, contact the service provider. ALM LED remains on. The power-on self-test may have failed. Unplug the unit and reapply power. If the alarm LED is still on, contact the service provider. ALM and TST LEDs are blinking. Firmware download may be in progress.
PAGE 15
Increasing the Number of End-User Systems A single end-user system is attached to the Hotwire 5620 RTU by using an Ethernet crossover cable. To increase the number of end-user systems, connect all end-user systems to an Ethernet hub using a straight-through cable. See Connecting the Ethernet Cable on page 11. The Hotwire 5620 RTU can support up to 32 end-user systems. Verify any changes with the service provider. Cables & Connectors This section is reference information.
PAGE 16
Ethernet interface connector uses an 8-pin, non-keyed modular plug. Use shielded twisted-pair CAT5 or better cables. — To connect to an Ethernet hub, use the straight-through connection. Ethernet Cable 8-Pin Straight-through Connection Pin # Function 1 10BaseT TX D+ 2 10BaseT TX D– 3 10BaseT RX D+ 4&5 6 7&8 8-Pin Plug Not used 10BaseT RX D– Pin #8 Not used Pin #1 98-16055a – or – — To connect directly to a PC with an Ethernet NIC card, use an Ethernet Crossover cable.
PAGE 17
Optional RTU Wall Placement The Hotwire 5620 RTU is designed for tabletop placement. The RTU can also be mounted on a wall. To mount the RTU, you will need: ❑ Three #6 pan-head screws with anchors (for example, molly bolts, plastic or lead anchors) ❑ Drill, and the correct size drill bit for the anchors ❑ Screwdriver A template with the dimensions for the three screws is provided. See RTU Hardware Template on page 18. Procedure To mount the RTU: 1.
PAGE 18
RTU Hardware Template 5.43" Front (LEDs) 7.
PAGE 19
Technical Specifications for the Hotwire 5620 RTU Item Specification* Height x Width x Depth With Feet 1.43" x 6.00" x 8.75" (3.64 cm x 15.24 cm x 22.23 cm) Without Feet 1.25" x 6.00" x 8.75" (3.15 cm x 15.24 cm x 22.23 cm) Weight 1 lb. 1 oz. (0.48 kg) Power Class 2 Transformer normal service input voltage range Input: 100 VAC (+10%), 50 Hz; 120 VAC (+10%), 60 Hz; or 230 VAC (+10%), 50/60 Hz Output: 18 VDC nominal at 0.
PAGE 20
! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord. 4.
PAGE 21
CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: Directive 73/23/EEC – Council Directive of 19 February 1973 on the harmonization of the laws of the member states relating to electrical equipment designed for use within states relating to electrical equipment designed for use within certain voltage limits, as amended by Directive 93/68/EEC.
PAGE 22
The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the equipment unless the changes or modifications are expressly approved by Paradyne Corporation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 23
4. If the RTU causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. 5.
PAGE 24
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.