MINI PTZ Network Mini Dome Cameras Quick Guide V1.
Safety and Compliance Information Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the Safety Instructions supplied with your equipment before installation and operation. Installation This device is a class A product and may cause radio interference. Take measures if necessary. Make sure the camera operates in an environment where the temperature and humidity meet requirements.
Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. Maintenance Caution: There will be risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. If there is dust on the glass window surface, remove the dust gently using an oil-free brush or a rubber dust blowing ball.
Regulatory Compliance FCC statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
LVD/EMC /RE Directive This product complies with the European Low Voltage Directive 2014/35/EU , EMC Directive 2014/30/EU and 2014/53/EU. WEEE Directive–2012/19/EU The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner. Battery Directive-2013/56/EC Battery in the product complies with the European Battery Directive 2013/56/EC.
Default IP, Username and Password Default IP address: 192.168.1.13 Default username: admin Default password: 123456 The default password is used for your first login. To ensure account security, please change the password after your first login. You are recommended to set a strong password (no less than eight characters). Packing List Contact your local dealer if the package is damaged or incomplete. The attachments may vary with models, please see the actual model for details.
∅129.0mm (5.1") ∅108.5mm (4.3") 143.6mm (5.7") 3-∅4.0mm (0.16") S100.0mm (3.9") Cable Connection The appearance and tail cable may vary with device model. Third-party device connected through RS485 interface IP Network Power adapter ALM_OUT_P/ALM_OUT_N/ALM_INPUT/GND For specifications, see the latest product datasheet.
Mount Your Camera Ceiling Mount You may adopt ceiling mount or wall mount as needed. Prepare hardware accessories by yourself. The following part takes ceiling mount as an example. Wall mount is similar to ceiling mount and therefore is omitted here. Make sure that the wall is capable of supporting the weight of the camera. 1. Install SD card (optional). Open the slot cover Insert the SD card along the arrow direction 2. Uninstall the adapter plate.
Rotate counterclockwise OPEN LOCK Adapter plate 3. Attach the sticker. Attach the sticker to the desired mounting place. 4. Fix the adapter plate to the ceiling. Knock expansion bolts into holes, and fix the plate to the ceiling with screws. Make sure that FRONT on the plate is in monitoring direction.
5. Install the camera. Secure the camera to the adapter, align FRONT on the plate with the gap between OPEN and LOCK on the camera, rotate the camera counterclockwise until it’s fastened. Lead the cable through the side slot opening on the camera to secure the cable, so that you may avoid opening a hole on the ceiling.
Disconnect from power before intalling or uninstalling Micro SD card. Otherwise, the device or the Micro SD card might be damaged. For recommended SD card specifications, contact your dealer or technical support. Access Your Camera Before you begin, check that: Your camera is operating properly and connected to the network. The PC you are using is installed with Internet Explorer 8.0 or later. Follow these steps to access your camera through the Web interface: 1.
Install the ActiveX at your first login. When the installation of the ActiveX is completed, open your IE to log in. For your first login with Windows 7, if the system does not prompt you to install ActiveX, follow these steps to turn off UAC: click the Start button, and then click Control Panel. In the search box, type uac, and then click Change User Account Control Settings. Move the slider to the Never Notify position, and then click OK. After UAC is turned off, log in again.
