L11 Pro User Manual Please read the user manual carefully before use and keep it properly.
Welcome Welcome to use Verefa Robot Vacuum Cleaner. We hope you can have a pleasant experience! If you have any questions or suggestions, you can contact us through the contact information provided at the bottom of the robot, and we will try our best to solve the problem for you.
Table of Contents 1. Safety Instructions 2. Product Overview Important Safety Instructions 01 2.1 What's in the Box 05 2.2 Product Anatomy(including Buttons 06 and Indicators) 3.1 Important Tips Before Use 10 3.2 Get Started 11 4.1 Main Functions 14 18 4.3 Other Functions 19 5.1 Routine Maintenance 20 5.2 Troubleshooting 25 5.3 FAQs 29 Basic Parameters 31 Energy Saving and Battery 32 Customer Service 33 3. Installation 4. Operation Instructions 5.
1. Safety Instructions ! " ! # $ ٥ % the product. ٥Keep the manual properly for future reference.
٥ * ! ! # # ! > " " " " # # " + # ! ٥ J + ! ! ! # # ! operating.
Battery and Charging ٥ / # " " ! ! # H * # # " " ٥ ^ # " ! ! # # ! " " # " ! + ! # # ! ! # ٥Do not place the charging base near a heat source, such as heating radiator.
Laser safety information ٥ * q ! ^w: zN{ |Hq$ Nq } + " # " + (especially children and pets) from looking directly at the laser emitter at close range.
2. Product Overview 2.
2.2 Product Anatomy (including Buttons and Indicators) A) Robot Vacuum Top View Buttons 7 # - $ 7 - Auto Cleaning $ & H " start Auto Cleaning. Recharge button - Recharge $ 7 ! ! + - Reset Wi-Fi $ 7 # # for 3 seconds to reset Wi-Fi.
Bottom View Main sensors Laser distance sensor Recharge sensor Wall sensor : : Side brush Roller brush Roller brush cover Roller brush cover buckle Wheels Recharge sensor Charging contact pins Dust box Filter cover buckle Filter cover } ! H Dust box cover buckle Dust box release button Auto-empty dirt port Circuit contact pins Auto-empty dirt Dust box cover port cover 07
B) Auto-Empty Charging Base ( Charging Base ) Front View Top cover Charging base status indicator ? H @ Solid White $ : " # the robot is not on the charging base* $ * # ! ! # < # J Flashing White (x3) $ ! < indication Solid Red $ / # ! ! cover is open Flashing Red $ w * Extinguishes after 10 minutes into standby mode Charging base location
Top View Dust bag guide rails : ! ! # Bottom View & + Air duct cover 09
3. Installation 3.1 Important Tips Before Use Prepare your home environment 1 : # > ! Robot before use, and remove easily fallen, fragile, valuable, and ] &+ ! # # ! ! " " !! # robot. 2 Fold the fringed edge of the decorative carpet underneath to prevent it from entangling the Robot. Avoid carpets that are very dark in color or thicker than 17mm.
3.2 Get Started 1) Remove protective items " + + on the robot to ensure the normal usage. 2) Install side brush Click 3) Place the charging base, connect the power supply and charge the robot 1 7 ! ! # ?* # ! # ! # Good Wi Fi coverage @ H 7 ! ! # robot can easily reach it. $ >0.
H & ! ! # Y H ! + ! $ H 7 ! ! # " # - In order to facilitate the robot to return to the charging base smoothly after cleaning, it is recommended that the robot is started from the charging base, and do not move the ! ! # ! ! 2 Connected t
1 / H ` # * ` install it. 2 Reset Wi-Fi. H 7 # # ? 7 # % ! # @ + * ! # > " ! # ! 3 Add a device.
4. Operation Instructions 4.
$ H ^ # # ! ! # ! !" ! # - When continuing to clean, please keep the robot to start in the original position and direction to avoid path disorder. H * # ! ! ! H & - q ӥ Recharge - Auto mode : Y ! # _ " # automatically return to the charging base for charging.
$ - Make sure that the robot starts each cleaing from the charging base. H / + # X ! ! ^ + " # # ! location. 1.5m ӥ Spot cleaning (only set via the app) - Use the remote control page of the app to start the ! * # ! q | - q | & !" # 1.5m starting point.
ӥ Room cleaning (only set via the app) C - Using the app, you can select one or more rooms on D ! * # the selected rooms, and automatically return to the charging base after cleaning. $ H * " ! smart map on the robot and set the deviders before you can use the room cleaning function. - After starting cleaning, the robot may enter the area outside the designated area.
ӥ Auto-empty dirt H & !$ H & !" # ! ! # " # the dust box. $ - The noise during auto-empty dirt is relatively loud. Please pay attention to the impact of noise on daily life. H & H # # ! !" # ! | 4.
4.
5. Maintenance and Troubleshooting 5.
$ H ! # + - Do not put the incomplete dust box into the robot, so as to avoid mistakenly triggering !" # H / # ! # - 1 2 4 5 3 2) Clean roller brush and roller brush cover 1 7 # + # # " # cover and the roller brush.
4 5 3) Clean the side brush 1 Pull out the side brush. 2 : # ! # install it back. 4) Clean caster wheel 1 Pry out the caster axle and pull out the caster # + 2 Clean the hair and dirt from the caster axle and caster body, and then reinstall and press it tightly.
6) Clean sensors, charging contact pins and charging contacts 1 Y $ H * + " ! / ! + ! " # $ " # When the dust bag is full, replace the dust bag according to the indicator light of the auto-empty charging base.
1 2 4 5 3 8) Clean the air duct ^ # " ! ! 7 > " H ! ! # # > 1 the front side facing up. $ H / H ! ! # + ! ! cover.
5.2 Troubleshooting ^ # !" ! # H ! ! # ! ! 7 + # ! # Indicator light Robot Flashing Red Solution Error 1: Front bumper stuck. Please clean and retry. - The front bumper is stuck. Please tap repeatedly + & " relocate it to start. Error 2: Side brush stuck.
Robot Flashing Red Error 12: Robot trapped. Please clear obstacles around. - The robot may be stuck or trapped. Please clear obstacles around the robot. Error 13: Charging base blocked. Please clear it. - The area around the charging base may be blocked by obstacles or dust. Please clean the ! ! # beacon area. Error 14: Charging error.
Indicator light Robot Flashing Red Solution Error F1: Side brush module fault. Please check and try restarting the system. H 7 # ! 7 + " # " on the system. - If the fault persists, please contact our customer service. Error F2: Roller brush module fault. Please check and try restarting the system.
Charging base Solid Red Please check whether the dust bag is installed and close the cover properly. H 7 # ! !" ensure that the dust bag is installed in place, and close the dust bag cover. - Please check the status of the dust bag cover to ensure that the dust bag cover is closed and Long time using dust bag, please replace the dust bag. - Please check the status of the dust bag and replace the dust bag in time.
5.3 FAQs Problem type Solution Unable to turn on. q@ ^ _ 7 ! ! # # " # ! ! # ! ! ! " + automatically start up. 2) If it still cannot be started, please try to restart the system.
Abnormal behavior. q@ 7 ! 7 the chapter "Troubleshooting". @ Y % % Maintenance". 3) Reboot the robot. The robot suddenly made a loud noise.
6.
Energy Saving and Battery Holiday energy saving mode - On the charging base, press and hold Recharge button for 10 seconds until a tone is heard, at ! + ! H ; ! + ! + " " " # H ! # + ! H * # + ! ! # # pressed.
Customer Service Customer Service ^ + X ! # ! ! & " # ! ! " best to help you solve it. Sincere Care, Always for You ̔ : + " " + " & ̔ + " + support@verefalife.
Product warranty card User name Mailing address Email address Phone number Model No.
: " & : + " " + " & + " + support@verefalife.
