User's Manual

ManualsBrandsZhejiang Libiao Robotics ManualsRoboticsCrossbelt Robot

Table Of Contents

空白页面

User Manual of LBCRB30 Crossbelt Robot

Brief Descriptions

LBCRB30 Crossbelt Robot are mainly used for sorting in industries of

express delivery services and warehousing logistics. Operated on special

sorting platforms, these robots can receive and execute orders from

servers to unload parcels and transport them to designated locations.

Product pictures:

2.Electrical Performance

Dimensions：660mm*483mm* 212mm

Summary of content (7 pages)

PAGE 1
User Manual of LBCRB30 Crossbelt Robot 1. Brief Descriptions LBCRB30 Crossbelt Robot are mainly used for sorting in industries of express delivery services and warehousing logistics. Operated on special sorting platforms, these robots can receive and execute orders from servers to unload parcels and transport them to designated locations. Product pictures: 2.
PAGE 2
Rated Load：30kg Transfer way：Belt Drive drive system：Servo Motor Set speed：1.5m/S Set acceleration：1.5m/S2 Communication mode：Wireless Working temperature:-10 ~ 55° Humidity: ≤95%（25℃）RH LIB：4.6VLi-Ion Charging voltage：3.8-5.4V MAX Charging current：90A Endurance：3H Charge style：Contact 3.Descriptions of Product Modules 3.1.BMSP module 3.1.1.BMSP module through the chassis module read RFID(13.
PAGE 3
In the power management module, commands for powering on and off robots can be obtained through wireless module. If a command for powering on robot is received, the power management module will switch on the power supply and power on all devices. When a command for powering off robot is received, the module will switch off the power supply and power off all devices. Meanwhile, all other devices will be switched to standby states with low power consumption except for the power management module. 3.2.
PAGE 4
Operation State Standby A B C Operation Shutdown Function SN The bright red LED indicator lights can indicate malfunctions. The states of the indicator lights are shown as follows: State of Indicator Light Descriptions of State Operation State Standby off off 2 off off 3 on for 0.5s and off for 1.5s 4 on for 0.5s and off for 0.5s 5 on for 0.5s and off for 1 off off off on for 0.2s and off for 4s off off on off on for 0.2s and off for 0.2s on for 0.2s and off for 0.
PAGE 5
Current State No. (see above table)） Buttons 1 Any 2 3-8 Press [A] + [C] for 3s Press [B] + [C] for 5s Description of Functions No function Power on and wake the robot up Power off and switch the robot to a standby state 3-6 Press [A] The robot enters the operation state 3-6 Press [B] The robot enters the shutdown state 3-6 Press [C] Enter the state of function selection (No.8 state). Later, you can switch to another function once you press [Function] and choose any one from No.1 to No.
PAGE 6
through the LBAP-102LU-900 wireless device of the swithing device.Then, the robot can be automatically powered on. 4.2.Sorting g Robot so orting can be b realized through the e server. You can contrrol the robots and exxchange da ata via wirelless module e with serve er software. The serrver will try connecting g all robots s which havve been po owered on..
PAGE 7
FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.