Manualshelf

Safety Instructions

ManualsBrandsZhejiang Lianda Science and Technology ManualsElectronicsRemote control
12
Zhejiang Lianda Science&Technology Co.,Ltd
Technological and Industrial District 2 # Road (313009) NanXun, Huzhou, Zhejiang-China
1.2.Check/Change(if needed) the Motor rotation direction
-Press UP button of the remote control.
If the direction is ok,
-Press the PROG button with a thin head
tool for 2sec. until the motr jogs.
If the direction is not ok,
-Press the STOP button for 2sec.until
the motor jogs, the direction is changed.
-Press the PROG button for 2sec.the motor
jogs..
Note:
*The operation should be done in 2min.after
the 1st remote control recorded.
*The direction can be changed again and again
by “STOP 2s”before confirmed by “PROG 2s”.
*The direction must be confirmed by “PROG 2s”
,and then the setting process will go to the next
step.
6.How to identify Radio motor with Manual limit setting and Radio motor with radio limit setting
If the radio motor shows an abnormal behaviour during the setup phase or during the factory mode reset,it may be that you are not referring to the
correct radio motor instruction:
Please ensure that you are using the correct radio motor instruction.
For Installer: check the radio motor head. If the radio motor head has a manual limit switch worm, it is a radio motor with manual limit setting. If not,
it is a motor with radio limit setting.
For User: the behaviour will only differ at the first remote setting or after a factory reset. If the radio motor loses the limit setting,it is a radio motor
with radio limit setting (for this type of radio motor, after a factory reset, the limit must be set up again, as well as the rotating direction.The Keyring
can not be used to do these two operations). Otherwise it is a radio motor with manual limit setting. (Only direction must be checked).
Check/Change the direction.
Prog
2 sec.
Feedback
Feedback
Prog
2 sec.
Feedback
I
I
I
I
1.3.Set the end limits(only for Radio motor with radio limit setting)
-Press the UP+STOP buttons until the motor jogs.
-Press the UP/DOWN button and stop the motor
where you want to set the up limit.
-Press the PROG button for 2sec. until the motor
jogs.
a). Set the up limit
-Press the DOWN+STOP buttons until the motor jogs.
-Press the UP/DOWN button and stop the motor
where you want to set the down limit.
-Press the PROG button for 2sec. until the motor
jogs.
b). Set the down limit
2 sec.
Feedback
STOP
Prog
2 sec.
Feedback
2 sec.
Feedback
STOP
Prog
2 sec.
Feedback
OK
OK
a.
I
I
I
I
OR
I
I
I
I
I
I
I
I
OR
I
I
I
I
I
I
I
I
I
I
I
I
b.
Note:
*The operation should be done after the direction
confirmed.
*No matter which limit should be set firstly.
*Before setting the end limits,the motor works in
step movement mode.
*The up limit should be above the down limit.
2).User Setting Mode:
Note: *The operation should be done in 2min., otherwise the motor jogs and back to the previous status.
*The setting could be cancelled by “UP+STOP+DOWN 0.5s” before confirmed by “PROG 2s”.
Feedback
N
1
Feedback
Prog
4 sec.
N
2
Prog
2 sec.
-Press the PROG button with a thin head tool on the already
recorded remote control/channel(N1) for 4sec. until the
motor jogs.
-Select the new remote control/channel to add(N2) and press
its PROG button for 2sec. until it jogs.
2.1.Add a Remote Control
Note:Up to 12 remote controls or channels can be added
to one motor.
-Press the PROG button with a thin head tool on the already
recorded remote control/channel(N1) for 4sec. until the
motor jogs.
-Select the already recorded remote control/channel to
delete(N2) and press its PROG button for 2sec. until it jogs.
2.2.Delete a Remote Control
Note:One remote control can NOT delete itself.
-Press the PROG button for 4sec. until the motor jogs.
-Press the UP+STOP buttons for 2sec. until the motor jogs.
-Press the UP/DOWN button and stop the motor where you
want to set the limit.
-Press the PROG button for 2sec. until the motor jogs.
2.3.Readjust the end limit(only for Radio motor
with radio limit setting)
Note:The motor work in step movement mode during
the setting process.
a).Readjust the UP end limit
-Press the PROG button for 4sec. until the motor jogs.
-Press the DOWN+STOP buttons for 2sec. until the motor jogs.
-Press the UP/DOWN button and stop the motor where you
want to set the limit.
-Press the PROG button for 2sec. until the motor jogs.
b).Readjust the DOWN end limit
Prog
4 sec.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
2 sec.
Feedback
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
OR
STOP
Prog
2 sec.
Feedback
Prog
4 sec.
2 sec.
OK
OK
a. b.
Feedback
Feedback
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
OR
STOP
Prog
2 sec.
Feedback
Feedback
2.4.Change the direction
-Press the PROG button for 4sec. until the motor jogs.
-Press the STOP button for 2sec. until the motor jogs.
-Press the PROG button for 2sec. until the motor jogs.
Note:The direction can be changed again and again by “STOP 2s”
before confirmed by “PROG 2s”.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Prog
4 sec.
Feedback
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Prog
2 sec.
Feedback
Feedback
2 sec.
2.5.Replace a Remote Control
-Switch the power off for 2sec.
-Switch the power on for 5 to 15sec.
-Switch the power off for 2sec.
-Switch the power on,the motor jogs.
-Press the PROG button on the new control for 0.5sec. until
the motor jogs:the new control is programmed and all the
recorded remote controls are deleted.
Note:The operation deletes all the recorded remote controls.
However the end limits are retained.
2 sec.
5~15 sec.
2 sec.
Prog
Feedback
Feedback
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
0.5 sec.
2.6.Reset the motor
-Press the PROG button for 4sec. until the motor jogs.
-Press simultaneously on UP+DOWN buttons for 2sec. until the
motor jogs.
-Press the PROG button for 2sec. until the motor jogs.
Note:*Any other operation will interrupt the reset process.
*The operation deletes all the recorded remote controls and end limits setting,the motor will back to Initial mode.
*After motor reset,you have 2min. to record a remote control(see Step ”1.Initial setting”).
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Prog
4 sec.
Feedback
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Prog
2 sec
Feedback
Feedback
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
2 sec.