Safety Instructions

ManualsBrandsZhejiang Lianda Science and Technology ManualsElectronicsRemote control

Zhejiang Lianda Science&Technology Co.,Ltd

Technological and Industrial District 2 # Road (313009) NanXun, Huzhou, Zhejiang-China

SCP-R1 & SCP-R5 Remote Control

Index

Read the safety instructions on the enclosed sheet carefully before you start installation. If these instructions are not

followed, manufacturer’s liability and warranty are forfeited.

Manufacturer is not liable for any change in the regulations and standards introduced following the publication of this manual.

Manufacturer hereby declares that the short range product complies with directive 2014/ 53/EU.

This product must be installed and programmed by qualified personnel. Read these instructions carefully before making the

connections.

Warning

The Remote Control is a short range emitter radio control

device for various applications such as blinds, shutters,

projection screens, awnings and more. It can be used to all

the Lianda RTL receivers(Some Receivers have limited

functions with the RTL, please read the complete instruction

for more information.)

1.Product Description

2.Technical Information

3.Functions

4.Open the emitter/Replace the battery

1.Product Description

2.Technical Information

.Frequency Band:433.92 MHz

.Temperature:-10 ℃ to +50 ℃

.B attery Type:CR2032 Lithium 3V DC(1&5 channels)

.Product Class:II( with installation completed)

The SCP-R1 Remote Control is able to control 1 group

of motor at most, The SCP-R5 Remote Controls are

able to control 5 groups of motors at most ( RTL motors

or motors equipped with RTL receives) .

The Remote Controls can be used to setup the limit

of the RTL Radio motor with radio limit setting .

3.Functions

[a ] : UP(control key)

[b ] : STOP( control key)

[c ] : DOWN(control key)

[d ] : LED( 1&5channels)

[e ] : PROG

[f ] : Selection key( 5channels)

4.Open the emitter/Replace the battery

1).Open the back cover.

2).Remove the old battery and place the new battery.

(1-5channels:CR2032 Lithium 3V)

3).Close the back cover.

5.Programming

1) .Initial setting

2) .User Setting Mode

6.How to identify Radio motor with Manual limit setting and Radio

motor with radio limit setting

= 433. 92MHz

50m

= 433. 92MHz

146mm

45mm

12.5 mm

5.Programming

1).Initial setting:

-Switch the power on.

-Press UP+ DOWN buttons of a remote control together.

-A Feedback will confirm that remote control has been

temporary memorized inside the memory of the tubular motor.

Note:*Below setting should be done step by step.

*If power off before finishing the initial setting

or time out, you should start from the 1st step

after power on.

*Feedback=jog: is a short up and down

movement of the motor.

1.1.Record the 1st Remote Control in a tubular motor:

Note: The operation should be done in 2min. after power

on or motor reset.

0.5 sec.

Feedback

SCP-R1

SCP-R5

FCC Notice:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation

Any Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Summary of content (2 pages)

PAGE 1
SCP-R1 & SCP-R5 Remote Control FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation Any Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 2
1.2.Check / Change ( if needed ) the Motor rotation direction 1.3.Set the end limits(only for Radio motor with radio limit setting) Feedback I I I 2 sec. 2 sec. a. b. Prog 4 sec. 4 sec. Feedback Feedback I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I STOP STOP Prog Prog 2 sec. 2 sec. I I I I I I I I Feedback OK I I I I I I I I I I I I I I I I I I Feedback 2 sec. I II I I I I I I I I I 4 sec.