Digital Indoor Monitor Quick Start Guide V1.0.
Foreword General This manual introduces basic operations of the digital indoor monitor (hereinafter referred to as "VTH"). Models 2-wire VTH that supports Wi-Fi. Non 2-wire VTH that supports Wi-Fi. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning DANGER Indicates a high potential hazard which, if not avoided, will result in death or serious injury.
About the Manual The manual is for reference only. Slight differences might be found between the manual and the product. We are not liable for losses incurred due to operating the product in ways that are not in compliance with the manual. The manual will be updated according to the latest laws and regulations of related jurisdictions. For detailed information, see the paper user’s manual, use our CD-ROM, scan the QR code or visit our official website.
Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it, and keep the manual safe for future reference. Operation Requirements ● ● ● ● ● Check whether the power supply is correct before use. Do not unplug the power cord on the side of the device while the adapter is powered on.
Table of Contents Foreword .................................................................................................................................................... I Important Safeguards and Warnings .................................................................................................... III 1 Structure................................................................................................................................................. 1 Front Panel.........................
1 Structure The VTHs have the same front panel but differ in the ports in the rear panel. One supports 2wire and the other does not.
Rear Panel (non 2-wire) Rear panel for non 2-wire model 2
2 Installation Preparations Do not install the VTH in harsh environment with condensation, high temperature, dust, corrosive substance and direct sunlight. In case of abnormality after powering on the VTH, cut off the power supply at once, and unplug the network cable. Power on after troubleshooting. Installation should be done by professional teams. Do not dismantle or repair the device by yourself in case of device failure. Contact after-sales service if you need any help.
3 VTH Configuration This chapter introduces the configuration of the VTH and digital outdoor station (hereinafter referred to as the “VTO”) to achieve the intercom function. Follow the instructions below to get started. Before You Begin Make sure that there is no short or open circuit in the VTO and VTH. Plan IP and number (working as a phone number) for each VTO and VTH. Make sure that the VTH and VTO are on the network segment.
Quick configuration Config mode 5
Set password for VTH Set password for VTO 6
Initialize the devices Configuring Network Parameters You can choose to connect to the network either through WLAN or LAN. 3.3.1 WLAN a) Tap WireLessIP, enter local IP, subnet mask and gateway that you plan for the VTH, and then tap OK. b) Tap WireLessIP, tap automatically. to enable the DHCP function to obtain IP information To enable the DHCP function, use a router with a DHCP function.
WLAN 3.3.
Configuring SIP Server SIP server SIP server Parameter Description Server IP When the platform works as SIP server, server IP is the IP address of the platform. When VTO works as SIP server, server IP is the IP address of the VTO. Network Port When the platform works as SIP server, the network port is 5080. When VTO works as SIP server, the network port is 5060. Username Register Pwd Domain Username Login Pwd Leave it as default. Registration domain of SIP server, which can be null.
Configuring VTH VTH configuration Configuring VTO 10
VTO configuration 3.6.2 Adding Main VTO 3.6.
4 Commissioning After the basic configuration is complete, check whether the intercom function can work. VTO Calling VTH Call VTH from VTO VTH Monitoring VTO A VTH can monitor VTO.
Door Monitoring device 13
Cybersecurity Recommendations Mandatory actions to be taken for basic device network security: 1. Use Strong Passwords Please refer to the following suggestions to set passwords: The length should not be less than 8 characters; Include at least two types of characters; character types include upper and lower case letters, numbers and symbols; Do not contain the account name or the account name in reverse order; Do not use continuous characters, such as 123, abc, etc.
8. 9. 10. 11. 12. 13. We recommend you to bind the IP and MAC address of the gateway to the device, thus reducing the risk of ARP spoofing. Assign Accounts and Privileges Reasonably According to business and management requirements, reasonably add users and assign a minimum set of permissions to them. Disable Unnecessary Services and Choose Secure Modes If not needed, it is recommended to turn off some services such as SNMP, SMTP, UPnP, etc., to reduce risks.
