Dahua IR Wi-Fi Bullet Camera Quick Start Guide V 1.0.2 Dahua Vision Technology CO.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
1 Packing List Device × 1 Screw Package ×1 QSG ×1 1
2 Product Appearance Figure 2-1 Please refer to the following sheet for more details about the device. SN Name ① ② Ethernet port Note The device can be directly connected to computer.
Figure 2-2 Please refer to the following sheet for more details about each component. SN Name ① Reset/ WPS (Wi-Fi Protected Setup) button ② Indicator light 1 ③ Lower cover ④ Micro SD card slot ⑤ Indicator light 2 ⑥ Waterproof ring ⑦ Wi-Fi antenna ⑧ Locking screw Sheet 2-2 Note: For reset, long press for 8 seconds and then the light off; For WPS (Wi-Fi Protected Setup), one quick press.
Please refer to the following sheet for more details about status of indicator light. Indicator light status Red light stably on Green light slow flashing Green light quick flashing Device status Booting Booting completed, await Wi-Fi config, enter smart config status; Wi-Fi smart config in progress, including WPS (Wi-Fi Protected Setup), management frame, etc. Wi-Fi connection succeeded, operate normally. Red and green lights flash alternately Device upgrade Red light slow flashing Network disconnection.
3 Operate by Easy4ip APP Step 1 Power on the device with power adapter. Step 2 Connect your smart phone to your Wi-Fi network. Scan the “Easy4ip” QR on the packing box, download and install the Easy4ip APP. Step 3 Open Easy4ip APP (take IOS as an example), tap “Login” to login the APP, see Figure 3-1. Please register an account for your first use. Figure 3-1 Step 4 Please tap “+” to add new devices after you log in your account.
Figure 3-2 Step 5 Scan the QR code on the back of the camera to get the SN, you can also tap “Continue without scanning” and manually input the SN number on the next page.
Figure 3-3 Step 6 Fill in the Username and Password of the new camera, both of which are admin by default.
Figure 3-4 Step 7 Select “Yes, config Wi-Fi”, and fill in your Wi-Fi password, then tap “Next”.
Figure 3-5 Figure 3-6 Step 8 Your Camera will be added to your account.
Figure 3-7 Note: If you have more cameras, please follow steps 4-8 to add them one by one. If you want to change the Wi-Fi signal, please reset the camera to factory default and repeat steps 4-8 to add the device.
4 Network Configuration The IP address of all the cameras is the same when leaving factory (default IP 192.168.1.108). To make the camera access to the network smoothly, please plan the available IP segment reasonably according to the actual network environment. NOTE: The camera can be configured only when the IP addresses of the camera and the computer are in the same network segment. Step 1 Power on the device with power adapter,Connect the device to computer. Step 2 Double click the “smart cms.
Step 4 Click the main interface. ,and double click the default IP, See Error! Reference source not found. for Error! Reference source not found.
5 Device Installation Important Before the installation, please make sure the installation environment can at least support 3x weight of the camera. Figure 5-1 Please see Figure 5-1 and Figure 5-2. Step 1 Dig holes on the installation surface (wall or ceiling). Step 2 Open accessories bag, take out expansion bolt and insert it into the hole you just dug. Step 3 Open accessories bag, take out installation screws. Tighten the screws to fix the device on the installation surface (wall or ceiling).
Figure 5-2 Step 5 Use cross screwdriver (in accessories bag) to loosen adjusting screw. Step 6 Adjust the device in all possible directions, and set its monitoring direction according to the requirements. Step 7 Use cross screwdriver to tighten the adjusting screws. Note: This quick start guide is for reference only. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice.
