Bullet Network Camera Quick Start Guide V1.0.
Foreword General This manual introduces the installation and operations of network camera. Read carefully before using the device, and keep the manual safe for future reference. Safety Instructions The following signal words might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
format) cannot be opened. ● All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. ● Please visit our website, contact the supplier or customer service if any problems occur while using the device. ● If there is any uncertainty or controversy, we reserve the right of final explanation.
Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it. Transportation Requirements ● Transport the device under allowed humidity and temperature conditions. ● Pack the device with packaging provided by its manufacturer or packaging of the same quality before transporting it.
regulations. ● Ground the function earthing portion of the device to improve its reliability (certain models are not equipped with earthing holes). The device is a class I electrical appliance. Make sure that the power supply of the device is connected to a power socket with protective earthing. ● The dome cover is an optical component. Do not directly touch or wipe the surface of the cover during installation. Operation Requirements ● The cover must not be opened while the device is powered on.
● Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the lens. When it is necessary to clean the device, slightly wet a soft cloth with alcohol, and gently wipe away the dirt. ● Clean the device body with a soft dry cloth. If there are any stubborn stains, clean them away with a soft cloth dipped in a neutral detergent, and then wipe the surface dry.
Table of Contents Foreword .........................................................................................................................................................................................................I Important Safeguards and Warnings ............................................................................................................................................. III 1 Introduction........................................................................................
1 Introduction 1.1 Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid water damage and prevent short circuits from occurring. For details, see the FAQ manual. Figure 1-1 Cables Table 1-1 Cable information No. Port Name Description Connects to the network through a network cable. 1 Ethernet port Do not connect both network cable and Wi-Fi at the same time. Inputs 12 VDC power. Be sure to supply power as instructed in the manual.
2 Network Configuration Device initialization and IP configurations can all be managed with the ConfigTool or through the web page. For more information, see the web operation manual. ● Device initialization is available on select models, and is required at first-time use and after the device is reset. ● Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the computer are on the same network segment.
Step 3 Select Auto-check for updates as needed, and then click OK to initialize the device. Step 4 If initialization failed, click Click Finish. to see more information. 2.2 Changing the Device IP Address ● You can change the IP address of one or more devices at a time. This section is based on changing IP addresses in batches. ● Changing IP addresses in batches is available only when the corresponding devices have the same login password.
3 Operating with DMSS Make sure that there are no obstacles and electromagnetic interference between the device and the router for best possible wireless performance. Step 1 Add the device. 1) Tap + button on the upper-right corner of the DMSS home page to scan the QR code on the camera. If your DMSS fails to scan the QR code, tap Manually enter SN. 2) Select Wireless Camera. Figure 3-1 Add the device Step 2 Configure the device hotspot.
Figure 3-2 Configure the device hotspot Step 3 Step 4 Configure the Wi-Fi. Select your Wi-Fi network from SSID list, and then enter the password. Configure the device information. 1) Create the device name and password. 2) Set the time zone, and then click Done.
4 Installation 4.1 Packing List ● Tools required for installation, such as the electric drill, are not included in the package. ● The operation manual and information on the tools are on the disk or the QR code. Figure 4-1 Packing list 4.
4.3 Installing Camera 4.3.1 Installation Method Figure 4-3 Installation method 4.3.2 Installing SD Card ● SD card slot is available on select models. ● Disconnect the power before installing or removing the SD card. Press the reset button for 10 seconds to reset the device. Figure 4-4 Install SD card 4.3.3 Attaching Camera Make sure that the mounting surface is strong enough to hold at least three times the weight of the camera and bracket.
Figure 4-5 Cable going through the side cable tray Figure 4-6 Cable going through the mounting surface 8
4.3.4 (Optional) Installing Waterproof Connector This part is needed only when a waterproof connector comes with the camera and the camera is used outdoors. Figure 4-7 Install waterproof connector 4.3.
