Dahua HD IR Vandal Proof Network Dome Camera User’s Manual Version 1.2.1 Zhejiang Dahua Technology CO., LTD.
Welcome Thank you for purchasing our Network camera! This user’s manual is designed to be a reference tool for your system.
Important Safeguards and Warnings ． 1 Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Table of Contents 1 2 3 General Introduction .............................................................................................................. 1 1.1 Overview ................................................................................................................... 1 1.2 Features .................................................................................................................... 1 1.3 Specifications ................................................................
1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology, which maximally guarantees the video quality. It supports the IR night vision function.
Support motion detect. Backlight compensation: screen auto split to realize backlight compensation to adjust the bright. Support video watermark function to avoid vicious video modification. Built-in IR light. Support IR night vision. 1.3 Specifications Specifications Please refer to the following sheet for network camera performance specification.
Video Motion Detect Video Loss 396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area threshold ranges from 0 to 100. Activation event: video storage, image snapshot, log, email SMTP and etc. Activation event: video storage, image snapshot, log, email SMTP and etc. Record Manual >Video detect>Schedule Record Priority Network Wire Network Wireless Network Network Protocol Remote Operation Access Protocol AUX Interface Reset 1-ch Enthernet port, 10/100 Base-T Ethernet ， IEEE802.
2 Structure 2.1 Component Components ponents You can refer to the following figure for component structure. See Figure 2-1. Figure 2-1 Component structure Please refer to the following sheet for detailed information. Component Component Name Component 1 Dome body Component 2 Dome enclosure Port Port Name Note Network data in/out and PoE. Port 3 Dome enclosure Note: Port 4 Power input port Some devices support PoE. do not Connect to DC 12V power, input power. 2.
Figure 2-2 Dimension illustration (1) Figure 2-3 Dimension illustration (2) 5
Figure 2-4 Dimension illustration (3) 6
3 Device Installation 3.1 Installation Steps Important Before the installation, please make sure the installation environments can at least support 3x weight of the camera. Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference. Step 1 Use inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner hex screws on enclosure.
Figure 3-1 Device installation illustration 1 Figure 3-2 Device installation illustration 2 8
Note: When you need to reset the device, press the “Reset” button in Figure 3-2 for 10 seconds while connecting device to power. When you need to use WPS function, press the “Reset” button in Figure 3-2 for 1 to 2 seconds while connecting device to power, then press WPS button on the router. Generally the device can be connected to corresponding router within 1 minute (supported by some series products).
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe” icon, you can see an interface. In the device list interface, you can view device IP address, port number, subnet mask, default gateway, MAC address and etc.
Figure 4-3 Login prompt After you logged in, the configuration tool main interface is shown as below. See Figure 4-4. Figure 4-4 Main interface For detailed information and operation instruction of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD.
5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. Make sure the network camera has connected to the network properly. Please set the IP address, subnet mask and gateway of the PC and the network camera respectively. Network camera default IP address is 192.168.1.108.
Figure 5- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 5- 3.
6 FAQ Bug I can not boot up the device or operate properly. Please click RESET button for at least 10 seconds to restore factory default setup. I can not upgrade the device via network. When network upgrade operation failed, you can use port 3800 to continue upgrade. I can not login the client-end or the WEB. For Windows OS 98 or Windows ME user, if you can not install the client-end or can not view after the installation. We recommend the win2000sp4 OS or install the client-end of the low version.
Appendix Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Pb Hg Cd Cr VI PBB PBDE Circuit Board Component ○ ○ ○ ○ ○ ○ Device Case ○ ○ ○ ○ ○ ○ Wire and Cable ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Packing Components Accessories O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
