Bullet Network Camera Quick Start Guide V1.0.
Quick Start Guide Foreword General This manual introduces the functions, configuration, general operation, and system maintenance of network camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
Quick Start Guide ● Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened. ● All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. ● Please visit our website, contact the supplier or customer service if any problems occur while using the device. ● If there is any uncertainty or controversy, we reserve the right of final explanation.
Quick Start Guide Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it. Transportation Requirements ● Transport the device under allowed humidity and temperature conditions. ● Pack the device with packaging provided by its manufacturer or packaging of the same quality before transporting it.
Quick Start Guide against lightning. For outdoor scenarios, strictly comply with the lightning protection regulations. ● Ground the function earthing portion of the device to improve its reliability (certain models are not equipped with earthing holes). The device is a class I electrical appliance. Make sure that the power supply of the device is connected to a power socket with protective earthing. ● The dome cover is an optical component.
Quick Start Guide ● Use the accessories suggested by the manufacturer. Installation and maintenance must be performed by qualified professionals. ● Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the lens. When it is necessary to clean the device, slightly wet a soft cloth with alcohol, and gently wipe away the dirt. ● Clean the device body with a soft dry cloth.
Quick Start Guide Table of Contents Foreword ........................................................................................................................................................................................................I Important Safeguards and Warnings............................................................................................................................................ III 1 Introduction .......................................................................
Quick Start Guide 1 Introduction 1.1 Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see FAQ manual. Figure 1-1 Cables Table 1-1 Cable information No. Port name Description Inputs 12 VDC power. Be sure to supply power as instructed in the manual. 1 Power input Device abnormity or damage might occur if power is not supplied correctly. 2 ● Connects to network with network cable.
Quick Start Guide 1.2 Connecting Alarm Input/Output The camera can connect to external alarm input/output device through digital input/output port. Alarm input/output is available on select models. Step 1 Connect alarm input device to the alarm input end of the I/O port. See Figure 1-2. Device collects different states of alarm input port when the input signal is idling and being grounded. ● Device collects logic "1" when input signal is connected to +3V to +5V or idling.
Quick Start Guide ● The alarm output on the web page is corresponding to the alarm output end of the device, which is also alarm output end of the I/O port.
Quick Start Guide 2 Network Configuration Device initialization and IP setting can be finished with the ConfigTool or on web page. For more information, see web operation manual. ● Device initialization is available on select models, and it is required at first-time use and after device is being reset. ● Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the PC stays on the same network segment.
Quick Start Guide ● If you select the Current Segment Search checkbox and the Other Segment Search checkbox together, the system searches for the Camera under both conditions. ● Enter username and the password when you want to change IP, configure the system, update the Camera, restart the Camera, and more. Step 5 Click OK. Step 6 Select one or several cameras in uninitialized status, and then click Initialize. Step 7 Select the cameras to be initialized, and then click Initialize.
Quick Start Guide Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates as needed. If neither, leave them unselected. Step 10 Click OK to initialize the Camera. Click the success icon ( ) or the failure icon ( Step 11 Click Finish. ) for the details. 2.2 Changing Device IP Address ● You can change IP address of one or multiple devices at one time. This section is based on changing IP addresses in batches.
Quick Start Guide Figure 2-4 Modify IP address Step 3 Select Static mode, and then enter start IP, subnet mask, and gateway. ● IP addresses of multiple devices will be set to the same if you select the Same IP checkbox. ● If DHCP server is available in the network, devices will automatically obtain IP addresses from DHCP server when you select DHCP. Step 4 Click OK. 2.
Quick Start Guide 3 Installation 3.1 Packing List ● The tool required for the installation such as electric drill is not provided in the package. ● The operation manual and related tool information are contained in the disk or the QR code, and the actual package shall prevail. Figure 3-1 Packing list 3.
Quick Start Guide 3.3 Installing the Camera 3.3.1 Installation Method Figure 3-3 Installation method 3.3.2 Installing SD Card (Optional) ● SD card slot is available on select models. ● Disconnect the power before installing or removing the SD card. Press the reset button for 10 seconds to reset the device.
Quick Start Guide 3.3.3 Attaching the Camera Make sure that the mounting surface is strong enough to hold at least three times of the weight of the device and bracket.
Quick Start Guide 3.3.4 Installing Waterproof Connector (Optional) This part is needed only when there is waterproof connector in the package and the device is used outdoors. Figure 3-7 Install waterproof connector 3.3.
Quick Start Guide
