Bullet Wi-Fi Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.0 ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.
Quick Start Guide Foreword General This manual introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning WARNING CAUTION NOTE Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
Quick Start Guide ⚫ occurred when using the device. If there is any uncertainty or controversy, please refer to our final explanation.
Quick Start Guide Important Safeguards and Warnings Electrical Safety ⚫ ⚫ ⚫ ⚫ ⚫ All installation and operation shall conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1. Note that the power supply requirement is subject to the device label. Make sure that the power supply is correct before operating the device.
Quick Start Guide ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ It is recommended to ground the device to enhance reliability. Do not touch the image sensor (CMOS) directly. Dust and dirt can be removed with air blower, or you can wipe the lens gently with soft cloth that is moistened with alcohol. You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with mild detergent.
Quick Start Guide Table of Contents Foreword .................................................................................................................................................... I Important Safeguards and Warnings .................................................................................................... III 1 Cable .......................................................................................................................................................
Quick Start Guide 1 Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see the FAQ Manual. Cable list For more information about cable ports, see Table 1-1. Table 1-1 Cable information No. Port Name Description 1 Ethernet Connects to network with network cable. Inputs 12V DC power. Be sure to supply power as instructed in the manual.
Quick Start Guide 2 Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or on web interface. ⚫ ⚫ ⚫ ⚫ Device initialization is required at first use or after the device being reset. Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the PC stay in the same network segment. Plan useable network segment properly to connect the device to the network.
Quick Start Guide Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2. Password setting Set and confirm the password of the devices, then enter a valid email address, and then click Next. The final setting interface is displayed. Password can be modified or reset in System Settings. Select the options according to your needs, and then click OK. The Initialization interface is displayed after initialization is completed.
Quick Start Guide Select the devices whose IP addresses need to be modified, and then click Modify IP. The Modify IP Address interface is displayed. See Figure 2-3. Modify IP Address Select Static mode, and then enter start IP, subnet mask, and gateway. IP addresses of multiple devices will be set to the same if you select the Same IP check box. ⚫ If DHCP server is available in the network, devices will automatically obtain IP addresses from DHCP server when you select DHCP. Click OK.
Quick Start Guide Main interface 5
Quick Start Guide 3 Installation Packing List ⚫ ⚫ The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool are contained in the QR code. Dimensions The following figures are for reference only, and the actual product shall prevail.
Quick Start Guide Installing Device 3.3.1 Installation Type 3.3.2 Installing Antenna 3.3.3 Installing SD Card (Optional) Disconnect the power before installing or removing the SD card. Press and hold the reset button for 10 s to reset the camera. 3.3.
Quick Start Guide Make sure that the mounting surface is strong enough to hold at least three times of the weight of the device and bracket.
Quick Start Guide Cable going through the side cable tray 3.3.5 Installing Waterproof Connector (Optional) This part is needed only when there is waterproof connector in the package and the device is used outdoors.
Quick Start Guide 10
Quick Start Guide 3.3.
Quick Start Guide 12
