EZ-IP HD Indoor Wi-Fi Dome Network Camera Quick Start Guide V1.0.
Foreword General This Quick Start Guide (hereinafter referred to be "the Guide") introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the Guide. Signal Words WARNING CAUTION Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
All the designs and software are subject to change without prior written notice. The product updates might cause some differences between the actual product and the Guide. Please contact the customer service for the latest program and supplementary documentation. There still might be deviation in technical data, functions and operations description, or errors in print. If there is any doubt or dispute, please refer to our final explanation.
Important Safeguards and Warnings Electrical Safety All installation and operation should conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1. Please note that the power supply requirement is subject to the device label. Make sure the power supply is correct before operating the device.
It is recommended to use the device together with lightning arrester to improve lightning protection effect. It is recommended to ground the device to enhance reliability. Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol. Device body can be cleaned with soft dry cloth, which can also be used to remove stubborn stains when moistened with mild detergent.
Regulatory Information The regulatory information herein might vary according to the model you purchased. Some information is only applicable for the country or region where the product is sold. FCC Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC conditions: This device complies with part 15 of the FCC Rules.
Table of Contents Foreword ..................................................................................................................................................I Important Safeguards and Warnings ...................................................................................................III Regulatory Information ......................................................................................................................... V 1 Introduction ......................................
1 Introduction Cable type might vary with different devices, and the actual product shall prevail. Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see the FAQ manual. Figure 1-1 Cable list For more information about cable ports, see Table 1-1, and for the pattern of the LED Indicator, see Table 1-2. Table 1-1 Cable information No.
2 Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or in web interface. For more information, see the WEB operation manual. Device initialization is available on select models, and it is required at first use or after the device being reset. Device initialization is available only when the IP addresses of the device (192.168.1.108 by default) and the PC stay in the same network segment.
The Device initialization interface is displayed. Step 6 Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting Step 7 Set and confirm the password of the devices, then enter a valid email address, and then click Next. The final setting interface is displayed. Password can be modified or reset in System Settings. Step 8 Select the options according to your needs, and then click OK.
Figure 2-3 Modify IP Address Step 3 Select Static mode, and then enter start IP, subnet mask, and gateway. IP addresses of multiple devices will be set to the same if you select the Same IP checkbox. If DHCP server is available in the network, devices will automatically obtain IP addresses from DHCP server when you select DHCP. Step 4 Click OK. 2.3 Logging in Web Interface Step 1 Open IE browser, then enter the IP address of the device in the address bar, and then press Enter.
2.4 Operation with Remote Monitoring App You can download the remote monitoring app and add your camera to the app to perform remote monitor on your phone. Step 1 Download and install the "iDMSS Plus" app from App Store or the "gDMSS Plus" app from Google Play. Step 2 Run the app, and then select Camera at the home interface. The Live Preview interface is displayed. Step 3 Tap the + sign, and then tap Add Device. The Add Device interface is displayed. See Figure 2-5.
Figure 2-6 Live preview 6
3 Installation 3.1 Packing List The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool are contained in the disk or the QR code, and the actual packing shall prevail. 3.2 Dimension Following figures are for reference only, and the actual product shall prevail.
3.3 Installing Device 3.3.
3.3.2 Detaching the Dome 3.3.3 Installing the Dome 3.3.4 Installing SD Card (optional) Press the reset button to start WPS pairing; press and hold the reset button for 10 s to reset the camera to factory settings.
IPC-D1B40P-W/IPC-D1B40N-W 3.3.5 Attaching Device Make sure the mounting surface is strong enough to hold at least three times of the weight of the device and bracket.
Cable going through the mounting surface 11
Cable going through the side cable tray 3.3.
