LCD Fish/Depth Finder User Manual ZHANGZHOU LILLIPUT ELECTRONIC TECHNOLOGY CO., LTD ADDRESS: Zong Si Road, Lan Tian Economic Development Zone, Zhangzhou, Fu Jian, 363005, China TEL：0596-2109323、2109661 FAX：0596-2109611 http://www.lilliput.com.cn & http://www.gdsun.com Email: sales@lilliput.com.
Dear Customer： ： Thank you for choosing Lilliput’s LCD fish finder. This product adopts high-performance embedded computer hardware. It is designed for operations under relatively harsh marine environments and featuring water prove, damp prove, corruption protection, wide voltage range protection etc. The delicately optimized design meets the requirements of all users in its applications to various conditions and occasions.
Contents 1. Introduction...............................................................................................3 2. Specification...............................................................................................3 2-1. Functions..........................................................................................3 2-2. Parameter..........................................................................................4 3. Installation...................................................
1. Introduction Your fishing system user interface is easy to use. A combination of menu, keys, different views, and situation-specific, customizable menus allows you to control the color on display. Refer to the following illustration, and see functions, views and menu systems for detail information. 1.4-WAY Cursor Control 2.MENU 3.VIEW 4.EXIT 5.POWER 6.Screen 2. Specification 2-1. Functions: 4.
4. Auto Mode: Auto range, auto sensitivity 5. Display waveforms: Anyway to set, display the waveform will not be interrupted 6. Interference suppression: automatic suppression of interference signals with frequency unwanted signal Interference suppression 7. Cursor operation: for any point on the screen depth measurement 8. Depth migration: ±5m 9. Alarm mode: fish alarm, depth alarm, battery alarm, temperature alarm 10. Resolution: 0.022 m 11. Screen split: vertical 12. Frequency: 83/200KHZ dual 13.
3-2.
3-3 Main Device Installation 3-4． ．Transducer Installation: Transducer is a precious front signal sensor. It must transport and install with care, no heavy pressure, fall off or working in the air. Painting and parasite should keep away from the surface of the transducer. The mounting location is very important and will affect the measure accuracy of the transducer directly. It is recommended to install it on the bilge where the surface is smooth and flat.
1) Ensure that ship at the horizontal position, and the hull does not tilt. 2) Holding the transducer bracket template for the boat to mark the two mounting holes. Center of two holes should be parallel to the surface. Ensure that the bottom of the template and the distance between the lower edge of the beam is about 0 ~ 5 mm.
3-5.
4. Display Window 4-1. Title Screen Turn on your device F403S by pressing the POWER key. The title screen is display until the F403S begins operation. The device will begin Normal or Simulator operation, depending on your choice. Press MENU to begin Simulator operation. The simulator data is available under this mode; however the recording function is unavailable under simulator mode. Otherwise it will enter normal operating mode. In normal mode there, enter the last visit of the view interface. 4-2.
14. Sonar Color: Standard, green, gray, reversed. User-set according to personal habits, default value: standard. 15. Underwater view: standard, white line. User-set according to personal habits, default value: white lines. 16. Cursor measurements: the screen does not pop up in any menu, press the four arrow keys in the "left" "right" measure. Measurement will pause the screen brush chart, four arrow keys can be measured on the target. Measurement data is always displayed at the bottom left.
4-3. Sonar Zoom View 1. Window 1: bottom of the depth, you can set the alarm current depth, degree, can be the rootAccording to the user needs to set off or display, default value is: open. 2. Window 2: The current input voltage, current-voltage alarm can be set; can display the user needs to set off or, by default is: Off. 3.
X2 X4 X6 X8 4-4. Dual Sonar View 1. Window 1: Bottom of the depth, you can set the alarm current depth, degree, according to the user needs to set off or display, default value is: open. 2. Window 2: The current input voltage, current-voltage alarm can be set; can display the user needs to set off or, by default is: Off. 3.
magnification, this separator is fixed split screen. Size is not automatically set. 12. 83KHz frequency sonar: the instructions on the left area of 83KHz frequency sonar. 13. 200KHz frequency sonar: indicates that the right area to 83KHz frequency sonar. 14. Depth contours: with three lines to the screen is divided into several equal portions, you can also turn off the menu, default value: off. 15.
4-6. Circular View 1. The first circle: underwater depth, you can set the alarm current shades. 2. The second circle: scale, scope and under the scope of which can be manually set, by default, the range of values: 0; next range is: Automatic. 3. The third circle: water surface noise, underwater echo, the second bottom echo, echo the bottom three: a. the water surface noise: often refers to blind spots, the transducer emission arising from the waveform. b.
5. Key Button Functions F403S user interface consists of a set of easy work with various on-screen views and menus to give you flexibility and control over your fishing experience. Your control heads has the following keys: 1. 4-WAY Cursor Control 2. MENU 3. VIEW 4. EXIT 5. POWER ① 4-WAY Cursor Control Four-in-one multi-function keys: composed of up / down, left / right arrow keys. The four keys have different functions under different menus. Up / Down key: up and down shift of the cursor in the menu.
⑤ POWER POWER key: A. Press to pop-up "light" / "background color" shortcut menu, and then setting through four-in-one multi-function key; B. Press the power button of 2S device. The device is powered on when pressing the POWER button. When the device is running, press the POWER key, the screen will display the message "Power off Countdown" over the countdown, the host immediately shut down and then release button; otherwise release after the operation is disabled. 6.
under different units. Value default as 0, measuring range adjustment according to the bottom of water. Menu will pop-up through either main menu or shortcut key. 4. Chart Speed :1-10 levels, short press to make step size adjustment effective immediately; long-keep press to make step size adjustment effective after release. This feature is to adjust the refreshing speed of sonar signal chart. The default value is "5". 5.
Value default as "off"(and the voltage alarm is disable). 5. The temperature alarm: Off, 1 ℃ ~ 50 ℃ interval of 1 as a step size. After setting the alarm, if the temperature is less than the current set value, it will be in red font and flashing on the screen. Value default as "off". 6. Alarm types: low, medium and high. For alarm levels and alarm volumes, different volumes in different levels when operating. Value default as "low". B． ．Sonar 1. Bean Select: 200K, 83K, 200K/83K mixed; default value: 200K.
C. Setup 1. Depth Units: Meter, Feet, Fathom; value default as "Meter". 2. Temperature Units: ℃, ℉; default as"℃". 3. Depth Offset: -5 to 5, is divided into 10 grades, step size is 1; change as different ship’s drafts. Value default as "0". 4. Temperature Offset: -5 to 5, is divided into 10 grades, step size is 1; adjust manually when the detected and the actual temperature are different. Value default as "0". 5. Reset: No, Yes. 6.
6-3 Brightness Adjustment 1. Brightness: 0-10 levels, step size is 1, through the shortcut key to pop-up shortcut menu, and then adjust the brightness through the left and right keys of "Four-in-one multi-function key". It’s effective immediately through short press and long-keep press. 2. Back Ground Color: blue, white, black, users can set as their favors, value default as "Blue".
7. PARAMETER Panel Input voltage Frequency Transmit power Range Accuracy Interference suppression Automatic range Automatic sensitivity The cursor measurement Simulations show that Fish identification Display mode Depth excursion Shallow water alarm Depth alarm Low voltage alarm Alarm type Width Enlarge Chart speed Emission rate Echo color Operating Temperature Safety Grade Protection Installation Dimension(LWD) Weight 4.
8. STANDARD ACCESSORIES Number Name Quantity Number Name Quantity 1 200K/83K Probe 1pcs 9 retreat line holder 1 pcs 2 Base bracket (KA4x22MM screws 8 pcs 10 Jack import slot 1 pcs 3 Jack import screws(KB3×9) slot 2 pcs 11 Device base 1 pcs 4 Line holder (KB2.
