User's Manual

ManualsBrandsZhan Xiang Technology ManualsElectronicsFlat Panel TV Bracket

Table Of Contents

Often to check the product, ensure the safety. Do not use corrosive

agent or alcohol or chemical cloth to clean.

6.Caution

1.Do not disassemble the product to repair by yourself.

Warranty for electricity is void after disassembled!

2.After you installed the appratus, please check the

expension screws and all fastenig devices every 3months,

and please do not use it and contact the local dealer if gets

loose,rusty or lost.

Http://www.xyz888.com.cn

Mail : mail@xyz888.com.cn

8. Reliability

Temperature and humidity condition:-20℃~+50℃,80%HR

Do not touch or push the

product by hand or other

object when it is working.

Check carefully to make

sure every parts are fast-

ened tightly before use.

This wall mount is intended for use only with the maximum

weight indicated. Use with heavier than the maximum weight

indicated may result in instability causing possible injury.

Warning:

7. Maintanance

USER'S GUIDE

Model: ZX-C23AG TV Stand

Length :690mm

Width:390mm

Height:1070mm

1. Specification

1-2 Installation Parts

1-1 Dimensions:

1070mm

90m

390

Adapter

TV bracket assembly

Post assembly

Adapter

Ø10*47mm Nylon

plastic plug

M5*25mm

Pan head screw

Cross

① 6pcs ② 2pcs ③ 2pcs ④ 10pcs ⑤ 10pcs

⑥ 2pcs

⑦ 2pcs ⑧ 2pcs

Tab

Plastic cushion

WasherPad

M6*18 Plastic

head screw

M6*50 m Hexagon

wood screw

flange

M6*12mm

Sink head screw

Cross

M5*23mm

head screw

Cross

Pan

M5*28mm

Sink head screw

Cross

⑨ 2pcs ⑩ 2pcs

Remote control

M6*10mm

Pan head screw

Cross

6pcs

1pcs

4pcs

Do not connect power

supply before fasten the

product.

Make sure wire and plug

are good before connecting.

Remote control

Glasses

Base plate

e s

d f

e f

st fl

oor g

Summary of content (4 pages)

PAGE 1
USER'S GUIDE Warning: Model: ZX-C23AG TV Stand 6.Caution Do not connect power supply before fasten the product. Make sure wire and plug are good before connecting. 1. Specification 1-1 Dimensions: TV bracket assembly Length :690mm Width:390mm Height:1070mm 1070mm This wall mount is intended for use only with the maximum weight indicated. Use with heavier than the maximum weight indicated may result in instability causing possible injury.
PAGE 2
Notice: Check all the parts as shown on the mannual included. If parts are missed or damaged, do not use it and please return to your local distributor. 1-3 Installation Tool(Not included) : 14MM 10MM Hammer Electric drill Spanner Cross screw driver Pencil 2. Electric Specification 2.1 Input Voltage/Current/Frequency: 100-240V/<1.2A/50~60Hz 2.2 Output Current:DC24V,3A 2.3 Motor Item Rated Voltage Motor DC24V Warning: Current Current Operating (NoLoad) (Rated Load) Temperature ≤0.7A ≤1.
PAGE 3
-7.After ensure that the above step is ok, please insert the power of this product. ( see diagram 7) It only uses special power to insert the power supply outlet of this product. Do not use other power. Indicator light Coding key Warning: Firstly,you must screw off the two screws on the fastener, and keep the fastener by yourself.Then screw up the two screws to the original place. ( see diagram 1) 3-1.Fix the base plate(A)and post assembly(B)by 6pcs of ① M5*25mm ( see diagram 1) Cross pan head screw.
PAGE 4
3-3. First, fix the main bracket on locking plate by 4pcs12 M6*10mm Flat head screw. Then insert the square tube into the hole of main bracket, fasten the square tube by 11 plastic head screws(location according to the stamping line on the square tube). Then fix the TV bracket at two end of square tube, fasten by plastic head screws. (Distance between two TV brackets is same to the holes distance of TV back cover, main bracket is considered as centre line.